Close
0%
0%

justin.m.riddle

Following
Send a private message
Similar accounts worth following
2 Followers
1 Following
0 Projects
0 Likes
justinmriddle
Send a private message

This user joined on 06/05/2014.

24.9k
403
105
286
lol travelling salesman problem
Project Owner Contributor

Travelling Hacker Box

benchoffBenchoff

791
14
12
9
COW = (California, Oregon, Washington).
Project Owner Contributor

TriState-COW, HackerBox

jeremy-gJeremy g.

370.1k
1.7k
154
1.3k
Building an HMD with no special parts, to make work easier and safer
Project Owner Contributor

Arduino Glasses a HMD for Multimeter

alain-mauerAlain Mauer

59.4k
313
13
224
An outside pole mounted aerial picks up 4G signals which are then filtered, amplified and re-transmitted through a second inside aerial.
Project Owner Contributor

Cell Phone 4G LTE Repeater / Booster / Femtocell

capt-flatus-oflahertyCapt. Flatus O'Flaherty ☠

40.3k
1.9k
15
114
An open-source, ultra-low cost, portable screening device for retinal diseases
Project Owner Contributor

Open Indirect Ophthalmoscope

ebin-philipEbin Philip

35.2k
852
58
290
HeartyPatch is a fully open-source, IoT connected, BLE enabled heart-rate variability & ECG patch with great accuracy
Project Owner Contributor

HeartyPatch: A single-lead ECG-HR patch with ESP32

ashwin-k-whitchurchAshwin K Whitchurch

30.9k
741
5
122
Bridging the gap between professional and DIY/hobbyist bench power supply
Project Owner Contributor

DIY programmable (SCPI) bench power supply

denisDenis

28.3k
155
7
89
A cnc mill designed to be able to machine aluminum
Project Owner Contributor

CNC Mill

jupdykejupdyke

24.9k
403
105
286
lol travelling salesman problem
Project Owner Contributor

Travelling Hacker Box

benchoffBenchoff

24.6k
383
14
269
A USB-flash sized GSM/GPS tracker with a wide array of features
Project Owner Contributor

USB TinyTracker

paulPaul

22k
204
81
223
The DIY laptop built entirely from PCB
Project Owner Contributor

ELLO 2M

knvdKn/vD

19.7k
169
32
113
Dual input 24 bit Multimeter with USB interface, single channel 10 bit USB oscilloscope, PWM out, 2 Ch Data-logger, R, C, Digital sniffer.
Project Owner Contributor

Multimeter +

romanRoman

15.4k
145
7
121
A safety glasses with a bluetooth enabled head mounted oled Display, to diplay data from your measuring device right into your view field.
Project Owner Contributor

Safety Glasses With B.T. Display for Multimeter

alain-mauerAlain Mauer

10.6k
643
4
48
A Redistribution of Jand's RepRap-XY CoreXY 3D printer, integrating modifications by sdavi and original modifications for improvement
Project Owner Contributor

RepRap-XY Iteration 2

avrAVR

10.5k
80
15
40
An Arduino Zero compatible open source smartwatch
Project Owner Contributor

Zerowatch

8bit-bunny8bit-bunny

6.8k
47
3
34
The laptop I made “The Pi-Berry Laptop” is built around the Raspberry Pi 2. It has 1GB RAM, Quad core CPU, 4 USB Ports and One Ethernet port
Project Owner Contributor

Pi-Berry Laptop-- The Classic DIY laptop

sahas-chitlangeSahas Chitlange

6.7k
31
10
18
A decorative indoor garden/greenhouse
Project Owner Contributor

VegeTerrium

leonLeon

6.6k
239
0
23
A Raspberry Pi based smart connected high-quality speaker
Project Owner Contributor

BoomBeastic mini

carlo-maria-curingaCarlo Maria Curinga

4.8k
616
14
123
A project for the people suffering from tremor,this device can be used to analyze the tremor frequency and stabilize it by using a gyroscope
Project Owner Contributor

Analysis and control of hand tremor

mohammedzeeshan77mohammedzeeshan77

4.2k
554
2
45
Heart Failure is a debilitating condition that most old people encounters. A PoC uses coded signals, Doppler and a sound ML classifier.
Project Owner Contributor

Early and low cost detection of Heart Failure

jean-pierre-le-rouzicJean Pierre Le Rouzic

View all

Share this profile

Share

Bits

AVR wrote 07/20/2016 at 23:17 • point

Thanks for the follow on the printer! 

  Are you sure? yes | no

justin.m.riddle wrote 07/21/2016 at 00:45 • point

No problem. I hope you dont mind if I steal a few ideas for the printer I'm designing. I just haven't found a printer on the market that does everything that I want it to, and yours is pretty close!

  Are you sure? yes | no

AVR wrote 07/21/2016 at 05:49 • point

no probs, the git hasn't been updated lately but look for an update, I'm gonna be adding the corners. Just about everything is finalized, I will be building mine in about two weeks. As I test it I plan to redesign the idlers and motor blocks as one pice parts.

  Are you sure? yes | no

Roman wrote 04/23/2016 at 12:57 • point

Hi Justin, thank you for the skull and following my project Multimeter+.

  Are you sure? yes | no

justin.m.riddle wrote 04/24/2016 at 02:00 • point

If you decide to sell those things, I'll be first in line for one.

  Are you sure? yes | no

Roman wrote 04/24/2016 at 02:27 • point

Thanks, once I get all the bugs out I am considering making it an open source kit. I will keep you posted.

  Are you sure? yes | no

Radu Motisan wrote 09/24/2015 at 20:33 • point

Thanks for following uRADMonitor! One of my other projects was semifinalist in last year's Hackaday prize, check it out here: https://hackaday.io/project/1662-global-radiation-monitoring-network

  Are you sure? yes | no

Send a private message to justin.m.riddle

Become cool instantly

Create your Hackaday.io profile like justin.m.riddle and many others

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday

Report user as inappropriate

You are about to report the user "justin.m.riddle", please tell us the reason.