Close
0%
0%

Josh Gadeken

Robotics and electronics hobbyist.

Colorado
Following
Send a private message
Similar accounts worth following
2 Followers
4 Following
1 Projects
35 Likes
josh-gadeken
Send a private message

This user joined on 10/06/2016.

9.9k
338
4
35
iRobot Roomba 690 enhanced with a Raspberry Pi Zero 2W and IMU.
Project Owner Contributor

Roomba RPi

josh-gadekenJosh Gadeken

94.1k
843
112
598
A high speed and high torque robotic actuator using low-cost brushless motors, custom controller, 3D printed parts and bearings.
Project Owner Contributor

3D Printed Robot Actuator

paul-gouldPaul Gould

91.9k
2k
26
453
A powerful, compliant actuator for legged robotics
Project Owner Contributor

OpenTorque Actuator

gabrael-levineGabrael Levine

72.4k
441
167
359
Motorized model of Mars rovers Curiosity and Perseverance For Under $500
Project Owner Contributor

Sawppy the Rover

rogerRoger

59.8k
481
82
337
AMS's new AS7265X 3-chip set promises a compact, 18-channel, 20 nm FWMH spectrometer for less than $25
Project Owner Contributor

Compact, $25 spectrometer

kris-winerKris Winer

38.8k
3.6k
15
347
A low-cost, high-performance bipedal walking robot
Project Owner Contributor

Blackbird Bipedal Robot

gabrael-levineGabrael Levine

27.8k
6.8k
17
195
Micro Smart LiDAR Sensor
Project Owner Contributor

MappyDot

bleckyBlecky

24.6k
383
14
269
A USB-flash sized GSM/GPS tracker with a wide array of features
Project Owner Contributor

USB TinyTracker

paulPaul

19.1k
65
15
48
My ROS (Robot Operating System) indoor & outdoor robot
Project Owner Contributor

Wild Thumper based ROS robot

humpelstilzchenHumpelstilzchen

17.3k
64
7
71
Automatic control of the kitchen skirting board. Lifts up to 1 kg, zero power consumption on standby.
Project Owner Contributor

Space saving robot vacuum cleaner garage

mikaMiKa

10.1k
114
9
94
Cheap, Open-source, safe, and compliant 6 - Axis 3d printed robotic arm based on Quasi direct drive BLDC drives.
Project Owner Contributor

CM6 - Compliant 3D printed robotic arm

petar-crnjakPetar Crnjak

8.1k
123
0
80
RR1 is an open-source, 6+1 degrees of freedom desktop robotic arm, mostly 3D-printed with joints powered by custom planetary gearboxes.
Project Owner Contributor

RR1: Real Robot One - a DIY Desktop Robotic Arm

pavel-surynekPavel Surynek

6.6k
78
4
68
3D Printed Quadrupedal Robot
Project Owner Contributor

TOPS

aaed-musaAaed Musa

3.9k
13
4
7
Reverse engineering the Shark RV1001AED series Robot Vacuum
Project Owner Contributor

Shark Robot Vacuum Reverse Engineering

jon-steelJon Steel

3.7k
9
4
7
Reverse engineering the Shark RV750 robot vacuum, and other vacuums with similar hardware.
Project Owner Contributor

Snark I-un Robot, Hacking the Shark ION RV750...

jon-steelJon Steel

3.6k
20
3
15
Add mapping & MQTT-interfacing with ESP8266 and an IMU
Project Owner Contributor

Old Roomba, new tricks

simon-jansenSimon Jansen

3.3k
1.2k
0
33
One of my most advanced projects to date. A tracked robotic development platform that [hopefully] raises the bar for hobby robotics.
Project Owner Contributor

Autonomous tracked robotic platform UGV

maximiliano-palayMaximiliano Palay

2.9k
45
2
40
Plant-Robot hybrid with actuators and electrical potential sensing for plant control
Project Owner Contributor

Plantoid

daniel-slttnesDaniel Slåttnes

2.9k
53
0
50
An easy to build spider robot kit.
Project Owner Contributor

Kubik M0

dehipudeʃhipu

View all

Share this profile

Share

Bits

Kris Winer wrote 08/03/2018 at 04:48 • point

Thanks for liking my $25 Spectrometer project!

  Are you sure? yes | no

Radu Motisan wrote 01/15/2017 at 16:19 • point

Hi, thanks for following the #Portable environmental monitor . It's a global network to measure and show the real data, uncensored. If you want your own unit and join this effort, use this contact form: http://www.uradmonitor.com/join-the-network/

  Are you sure? yes | no

Send a private message to Josh Gadeken

Become cool instantly

Create your Hackaday.io profile like Josh Gadeken and many others

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday

Report user as inappropriate

You are about to report the user "Josh Gadeken", please tell us the reason.