Close
0%
0%

WiFi Webradio on ESP8266 or ESP32

KaRadio
A fully featured wifi web radio player with only low cost boards.
with or without a vs1053 board

Similar projects worth following
Control with any browsers (ie edge, chrome mozilla etc...).
or with an external hardware panel or with the uart interface or with telnet.
Memory for 255 stations
OTA (On the Air) upgrade,
Read direct mp3 or ogg or WMA streams or playlist .pls .m3u, asx and .xspf
Read up to a 320 kb/s stream,
Encoder, IR, lcd ...
Embedded wifi configuration via the web or serial or telnet.
Metadata displayed (ie Title of the current song if given in the stream),
Permanent setting (sound setting, stations, wifi)
Server multi clients with automatic refresh (websocket),
The stations may be downloaded and uploaded within the web site,
Stations sort management by drag drop.
very quick responsive web by caching local information in the browser and websocket.
additional hardware: a led indicates the state of the equipment
Optional: control switches, lcd display, additional ram for buffering

See http://www.instructables.com/id/Wifi-Webradio-With-ESP8266-and-VS1053 for the description of the minimal prototype.

See Github for sources

See github source for the ESP32 version ( vs1053 or i2s or pcm or internal DAC)

See A project derived from KaRadio32 in progress.

See the lcd +IR software's on Github AddOn

See some realizations of users at KaraDio

A nextion touchscreen display for KaraDio from yo2ldk : Here

For more informations or questions, you can enter to the Karadio facebook group


KaRadio32 Release 1.9


KaRadio32:

Release 1.9 Rev6 - Built on 2020/01/11

New:

  • 1.9 R7
    • New telnet or serial commands: cli.wake, cli.sleep:
      cli.wake("x"): x in minutes. Start or stop the wake function. A value 0 stop the wake timer cli.sleep("x"): x in minutes. Start or stop the sleep function. A value 0 stop the sleep timer cli.wake: Display the current value in seconds cli.Sleep: Display the current value in seconds
    • sys.lcdstop, sys.lcdblv: sys.lcdstop and sys.lcdstop("x"): Timer in seconds to switch off the lcd on stop mode. 0= no timer sys.lcdblv and sys.lcdblv("x"): Value in percent of the backlight.
    • Fade in and out for backlight driven by a gpio.
    • New tool and hardware partition from Bazooka07: Update for boards/nvs_generator.sh use nvs_partition_gen.py tool directly from $IDF_PATH folder can process one or all boards in one shot. Update size for binary partition : 0x3000 now ! Look at : https://docs.espressif.com/projects/esp-idf/en/latest/api-reference/storage/nvs_partition_gen.html#running-the-utility
    • Decode url correctly for /webStation. included name #149
    • Esp-idf Release 3.3.1
    • https://github.com/karawin/Ka-Radio32/releases
  • 1.9 R6:
    • Parse playlist fix.
  • 1.9 R4:
    • wifi.auto command now disable the AP mode if already connected to an AP in the past.
    • I2S corrected for 32bit output stream. Thanks to har-in-air github user.
    • Instant play: new button "Add/Edit", and update fields on cli commands.

KaRadio: Release 1.9

Release 1.9 R6 - Built on 2020/01/11

New:

  • 1.9 R6:
    • Parse playlist fix.
  • 1.9 R4:
    • LWIP layer tuned. Better errno 11 computing.

History:

history

For ESP32 see the github page KaRadio32. Release 1.6 R4

ESP8266 Simplest prototype:

- Optional external ram (23LCV1024) support (1:CS/=GPIO16 2:MISO=GPIO12 3:NC 4:GND 5:MOSI=GPIO13 6:SCK=GPIO14 7:GND 8:3.3v)

Attention:
The optional led is now on GPIO2. The blue led on the ESP8266 is blinking at the same rate.
GPIO16 is now the Chip select for the external ram if any.
The external ram is detected at boot time if present.

To upgrade to this release, please flash user1.4096.new.4.bin at 0x1000 ,
user2.4096.new.4.bin at 0X81000 and blank.bin at 0x7e000 & 0x3fe000
After that, all next updates are done with the On The Air (OTA) feature.
New binaries are hosted at http://karadio.karawin.fr .

Loading the esp8266

First use

  • If the access point of your router is not known, the webradio initializes itself as an AP. Connect your wifi to the ssid "WifiWebRadio",
  • Browse to 192.164.4.1 to display the page, got to "setting" "Wifi" and configure your ssid ap, the password if any, the wanted IP or use dhcp if you know how to retrieve the dhcp given ip (terminal or scan of the network).
  • In the gateway field, enter the ip address of your router.
  • Validate. The equipment restart to the new configuration. Connect your wifi to your AP and browse to the ip given in configuration.
  • Congratulation, you can edit your own station list. Don't forget to save your stations list in case of problem or for new equipments.
  • if the AP is already know by the esp8266, the default ip at the first start is 192.168.1.254
  • a sample of stations list is on https://github.com/karawin/Ka-Radio/blob/master/ESP8266-Firmware/WebStations.txt...
Read more »

KaRadio32.bin

KaRadio32 1.9 Rev 7 Updated

octet-stream - 1.43 MB - 02/14/2020 at 22:20

Download

user2.4096.new.4.bin

KaRadio 1.9 Rev 6 Partition 1

octet-stream - 421.50 kB - 01/11/2020 at 18:13

Download

user1.4096.new.4.bin

KaRadio 1.9 Rev 6 Partition 2

octet-stream - 421.50 kB - 01/11/2020 at 18:13

Download

octet-stream - 3.98 kB - 09/17/2017 at 10:26

Download

octet-stream - 4.00 kB - 07/21/2016 at 15:19

Download

View all 6 files

View all 6 components

View all 11 project logs

  • 1
    Step 1

    Wiring:

    From ESP8266_ESP12( 3.3 v) or nodeMCU(5v) to VS1053 (5 v)

    REST:

    ADC : gound if control panel not used

    CH_PD to 3.3v

    GPIO16 led output

    D5:GPIO14 to VS1053 SCK

    D6:GPIO12 to VS1053 MISO (or so)

    D7:GPIO13 to VS1053 MOSI (or si)

    TXD to CH340G UART rx

    RXD from CH340G UART tx

    D1:GPIO05 to VS1053 XDCS

    D2:GPIO04 to VS1053 DREQ

    D3:GPIO00 to VS1053 XRST

    GPIO02

    D8:GPIO15 to VS1053 XCS

View all instructions

Enjoy this project?

Share

Discussions

ldv82 wrote 05/16/2017 at 09:44 point
What are the advantages of ESP32? Any new functions will be at the radio?

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/16/2017 at 09:53 point

Don't know yet ;-)
Just for fun and may be bluetooth, but I have to learn it before.

  Are you sure? yes | no

ldv82 wrote 05/15/2017 at 13:54 point

jp cocatrix 

Do not plan a version STM32+SSD1306+encoder?

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/15/2017 at 22:32 point

Yes, i'am working on it. Some technical problem with u8glib ...

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/30/2017 at 16:33 point

Too busy to study the STM32. I have one but unpacked for the moment.

  Are you sure? yes | no

Roman wrote 05/13/2017 at 15:29 point

HI,Problem! Radio sometimes stops working (hangs)!!!!

Thanks

Best regards,
~~ Roman

  Are you sure? yes | no

Flex wrote 05/14/2017 at 15:04 point

Hey,

I’ve got a similar problem, sometimes stops the VS Coding and needs a reset. The NodeMCU and Website keep working well, but the speaker didn’t get a signal from the decoder. It seems to happen randomly, sometimes after 20min and othertimes the systems run over hours perfectly.


I use an NodeMCU connected to an Arduino (for the OLED and a FM transmitter), buttons and such an VS1053: http://www.ebay.de/itm/VS1053-MP3-Module-Development-Board-w-On-Board-Recording-Function-SPI-Interface-/291596880495?hash=item43e4874a6f:g:gm4AAOSwEK9Tw2qE

It could be a pointer issue of the VS, when I stream from my Shoutcast-Server with 320kbps stereo it feels like the problem comes earlier as if I stream with 98kbps mono signal.

Greets

Felix

  Are you sure? yes | no

cwojtala wrote 05/03/2017 at 11:49 point

Hi, i've got an issue. I flashed the esp8266 with the esptool like this:

esptool.py write_flash 0x000 boot_v1.6.bin 0x01000 user1.4096.new.4.bin
0x81000 user2.4096.new.4.bin 0x7e000 blank.bin 0x3fe000 blank.bin
0xfc000 esp_init_data_default.bin 0x3fc000 esp_init_data_default.bin

and it seemed to work. i can connect to the AP but when i fill in the SSID ans password an then click validate nothing happens, after a reset its still in ap mode....

pls hlp

chris

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/03/2017 at 13:46 point

dhcp, or ip,mask,  gateway?

In dhcp the ip may be read on the uart interface.

  Are you sure? yes | no

cwojtala wrote 05/03/2017 at 13:59 point

i.ve tried both. it starts always in ap mode again

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/03/2017 at 14:01 point

check with a terminal on the usb com port. You will see the error. Certainly a bad password.

  Are you sure? yes | no

cwojtala wrote 05/03/2017 at 14:51 point

dont ask m how but after a couple resets ist working now. what i observed is tha at the beginning there was no mac adress next to the wlan security options, but now is is there and its working. thx for this very cool project

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/03/2017 at 14:23 point

notice that the validate will reset automatically. It is the validate on right of the Wifi & Network label

  Are you sure? yes | no

Vishal Dhayalan wrote 04/22/2017 at 22:51 point

Hi again, can you also tell me which files i need to flash onto the ESP8266 NodeMCU and any other details required in this process? There seems to be more files in the 'files' section, than shown in the images on instructables for this project... Thank you.

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/03/2017 at 13:50 point

Which one?

  Are you sure? yes | no

Vishal Dhayalan wrote 04/22/2017 at 22:48 point

Hi, is it possible to add IR-Remote alone, without a display? and i would like it to just run on the esp8266 NodeMCU, without an arduino, as I'm trying to run on a minimum setup with basic user controls. Love all the effort and time you've put into this! Thank you.

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/03/2017 at 13:48 point

no, not without arduino mini pro. But you can have IR remote without display. Just don't add it.

Thanks

  Are you sure? yes | no

Paul wrote 04/14/2017 at 01:41 point

Hi, the ntp client is a fantastic new feature, for some reason the time is returning as UTC +1. When I add my tzo ("+8") the clock reads one hour ahead. I have changed my tzo to +7 to give me the correct time for now. Will you be correcting this in the future. We don't have dst where I live, so thats not the issue.

Thanks for all your hard work on this project :) 

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 05/03/2017 at 13:52 point

No, it is a simplified implementation.

  Are you sure? yes | no

cwojtala wrote 04/09/2017 at 12:12 point

I'm a little  bit confusedFirst: if i connect the buttons to the adc, do i have to change the firmware in the esp8266?

And second: i've odered this Module: 

VS1003B VS1053 MP3 Module Development Board Onboard recording function

 http://s.aliexpress.com/veUV3iiU 
(from AliExpress Android)

Does ist work with ist? If yes, how do i connect it to the ESP Board?

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 04/09/2017 at 12:43 point

1/ No, it is auto detected in software.

2/ Not sure, it is a vs1003. Partial support only by Karadio. Some doesn't work at all.
Th wire is well noted on the board. Same as vs1053.

  Are you sure? yes | no

cwojtala wrote 04/10/2017 at 11:48 point

thanks. Knowing my luck, my board won't work. But i can tell when it arrive from china

  Are you sure? yes | no

Eugene wrote 04/18/2017 at 16:13 point

This board works correctly with this project, have the same one

  Are you sure? yes | no

fjs1 wrote 04/04/2017 at 12:47 point

A really fantastic piece of work !  It works better than all IP radios (commercial) I had before.

Congratulations et Merci !

Franz

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 04/04/2017 at 12:50 point

Thanks.
Yes, a bit hard to code but so exciting...

  Are you sure? yes | no

vanilinman wrote 04/01/2017 at 23:01 point

I solved the problem of crackles.I shorten the loop of wires between the modules (I connected without a breadboard).Thanks for the tips.

  Are you sure? yes | no

vanilinman wrote 04/01/2017 at 21:48 point

Thank you. You are super. It began to play. Please tell me how to get rid of crackles in the headphones. I tried various sources of power, it does not help.

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 04/01/2017 at 21:52 point

I don't have this problem.

Check the ground wires (try another gnd entry may be) and try to short it (and all other....
Enjoy.

JP

  Are you sure? yes | no

vanilinman wrote 04/01/2017 at 20:54 point

Hello friends. Help is needed. I picked up the radio for Wemos D1 Mini following the instructions, but it does not want to play. The port writes:
##CLI.STOPPED# from playStationInt
##CLI.NAMESET#: 1 Record
##CLI.URLSET#: air.radiorecord.ru:8101/rr_320
##CLI.PATHSET#: /Icecast 2.3.3-kh10
##CLI.PORTSET#: 80
##CLI.OVOLSET#: 104
##CLI.STOPPED# from clientConnect

##CLI.VOL#: 254

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 04/01/2017 at 21:02 point

url: air.radiorecord.ru

Port: 8101

Path: /rr_320

And it will work.

##CLI.STOPPED# from Post instant_play
##CLI.URLSET#: air.radiorecord.ru
##CLI.PATHSET#: /rr_320
##CLI.PORTSET#: 8101
##CLI.OVOLSET#: 0
##CLI.VOL#: 72
##CLI.ICY0#: Radio Record
##CLI.ICY4#: Dance
##CLI.ICY5#: 320
##CLI.ICY7#:  ice-samplerate=44100;ice-bitrate=320;ice-channels=2
##CLI.PLAYING#
##CLI.META#: Bounce Inc - Faith

  Are you sure? yes | no

Thomas wrote 02/18/2017 at 09:50 point

Hi JP, how is the correct Syntax to Change UART Baud over Browser?

  Are you sure? yes | no

Thomas wrote 02/18/2017 at 10:05 point

Hi JP, i already found but dont understand. Is it 192.168.2.136/sys.uart("19200") for example? This Dont Work so i guess my Syntax ist wrong

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 02/18/2017 at 10:11 point

Two different interfaces: 
On browser:

192.168.2.136/?uart   revert the uart to 115200 until a reset. Useful in case you don't remind the current speed.

But on the uart interface (serial on tx rx)
sys.uart("115200")
Or other speed to change the uart baud rate on the next reset and forever until another sys.uart command.

115200 is the default. Before connecting a display controller, you must change to 28800.

  Are you sure? yes | no

Thomas wrote 02/18/2017 at 10:23 point

Ok, its a pitty. I  thought it could be adjusted on browser also. Is it possible to read the curren setting of baud on the browser? I unfortunatly have no communication between display controller and Esp . And want to check this first before Disassemble my Radio to connect it to a computer.

  Are you sure? yes | no

Thomas wrote 02/20/2017 at 11:07 point

Hi JP i know that your Standard setting is 28800. But i changed it both to 19200 because 28800 is not selectable with Arduino Serial Monitor. This works fine for me, also with IR Receiver on a pro Mni with 8 Mhz and 3,3 Volts.

In the past i had sometimes trouble with self changing settings on the Baudrate.

But in this case i checked now with computer, it hasnt changed.  I detached the esp Module and mount it again, and now Display works again.

It seems that my build on a protoboard is not much better than on a breadboard.

Regards

Thomas

  Are you sure? yes | no

Sergio wrote 02/13/2017 at 17:01 point

Hi JP, its posible to replace the VS1053 by a Bluetooth, to play the streams on some audio equipments or BT earphones?

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 02/13/2017 at 17:17 point

To replace the vs1053? No, absolutely no, it is the stream decoder (mp3 aac etc).
But you can add a bluetooth transmitter after to send audio.
http://www.ebay.com/itm/EEEKit-Bluetooth-Transmitter-Receiver-Wireless-A2DP-Stereo-Audio-Music-Adapter-/192080524398
https://www.aliexpress.com/item/Bluetooth-launch-module-CSR57E6-bluetooth-audio-transmitter-module-DC5-24V/32780319150.html?spm=2114.01010208.3.25.IYofEc&ws_ab_test=searchweb0_0,searchweb201602_4_10065_10068_10000074_10000032_119_10060_10062_10056_10055_10000062_10054_10059_10099_10000013_10103_10102_10000016_10096_10000056_10000059_10052_10053_10107_10050_10106_10051_10000097_10000094_10000053_10000007_10000050_10084_10000100_10083_10000047_10080_10082_10081_10110_10111_10112_10113_10114_10115_10037_10033_10000041_10000044_10078_10079_10077_10000038_10073_10000035_10122_10121,searchweb201603_10,afswitch_2,ppcSwitch_5,single_sort_1_default&btsid=009badba-8b67-45c2-af4c-2ccb512e3c12
https://www.aliexpress.com/item/High-Quality-Mini-3-5mm-Bluetooth-Audio-Transmitter-A2DP-Stereo-Dongle-Adapter-for-TV-Mp3-Mp4/32783336194.html?spm=2114.01010208.3.83.nyyA3a&ws_ab_test=searchweb0_0,searchweb201602_4_10065_10068_10000074_10000032_119_10060_10062_10056_10055_10000062_10054_10059_10099_10000013_10103_10102_10000016_10096_10000056_10000059_10052_10053_10107_10050_10106_10051_10000097_10000094_10000053_10000007_10000050_10084_10000100_10083_10000047_10080_10082_10081_10110_10111_10112_10113_10114_10115_10037_10000041_10000044_10078_10079_10077_10000038_10073_10000035_10122_10121,searchweb201603_10,afswitch_2,ppcSwitch_5,single_sort_1_default&btsid=7bf82844-0d36-4b60-b01b-2619dfaded88

  Are you sure? yes | no

jan wrote 02/12/2017 at 15:40 point

Hi JP the ESP 8266 is not starting when I connect it to the USB port I have to press the reset button on the ESP 8266 to start it up  then its going oke

is it possible to get it started directly ? or by a command from Arduino

Is it possible to get time information sent to tx

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 02/12/2017 at 21:29 point

Not sure to be able to do something for that. May be a weak usb?.
It works ok here.

The time is only on the browser for the moment. Do you need the time for displaying on the lcd?

  Are you sure? yes | no

jan wrote 02/12/2017 at 21:36 point

Yes i like the time on the Nextion diplay

  Are you sure? yes | no

jan wrote 04/15/2017 at 19:18 point

Thanks JP for the time for the display I not yet have it fix for my self butt will at it soon to the screen.

  Are you sure? yes | no

Sergio wrote 02/06/2017 at 05:02 point

Hi JP, since update 1.14 or 1.1.5and 1.1.6, i have something extrange with my player, after 30 min of playing the player stops alone. i have to push again the play button to continue listening a radio station. i testing for some hours and this problem happend every 30 min. can you check the sleep/wake code? Thanks.

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 02/06/2017 at 06:50 point

When the stream disappear, a connection is retried once.
In Log you see:
##CLI.STOPPED# from try restart
##CLI.PLAYING#
##CLI.PLAYING#
##CLI.STOPPED# from data not played

The timeout is 10 seconds for a registered station and 2 seconds for an instant play.


The wake/Sleep code has nothing to do here.

  Are you sure? yes | no

Sergio wrote 02/06/2017 at 14:47 point

Thanks JP for your help, now i see this in log

##CLI.STOPPED# from try restart
##CLI.STOPPED# from clientConnect
##CLI.PLAYING#

But no sound on the speakers

i have to reset de player

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 02/07/2017 at 13:16 point

You are right, a problem found when the stream disappears for a while.
I will debug. Thanks

  Are you sure? yes | no

yo2ldk wrote 02/03/2017 at 19:15 point

I publish my project with all need it to adapt the Nextion touchscreen on KaRAdio:

  https://hackaday.io/project/19707-nextion-touchscreen-display-for-web-player-karadio

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 02/03/2017 at 20:15 point

Great.
JP Means Jean-Pierre ;-)

  Are you sure? yes | no

jan wrote 01/31/2017 at 20:29 point

Hi I have a question is it possible to connect a Nextion touch screen to it to control the radio

I love the web radio and the possibility to  update it thru the web interface I like to use this project to at it in a shower project I`m doing at this moment the Nextion wil be built in to controle the shower like temp end the 6 massage jets I like to ad the web radio into this project     

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 01/31/2017 at 20:40 point

https://hackaday.io/yo2ldk done  it. Contact him.

  Are you sure? yes | no

ldv82 wrote 01/31/2017 at 18:54 point

Send commands sys.patch ( "0"). How do I know if it is adopted? Thank you. Everything worked. But I did not understand why. Many times you enter a command sys.patch ( "0"), but it did not help. More will not upgrade the firmware unnecessarily in this.

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 01/31/2017 at 20:03 point

##CLI.URLSET#: stream.pcradio.biz
##CLI.PATHSET#: /Ruki_Vverh-low
##CLI.PORTSET#: 8000
##CLI.OVOLSET#: 0
##CLI.VOL#: 79
Header: Moved
##CLI.STOPPED# from C_HEADER
##CLI.URLSET#: 85.25.43.52
##CLI.PATHSET#: /Ruki_Vverh-low
##CLI.PORTSET#: 8000
##CLI.ICY0#:  Ruki_Vverh
##CLI.ICY3#:  http:\/\/www.pcradio.ru\/
##CLI.ICY4#:  Misc
##CLI.ICY5#:  24
##CLI.ICY6#:  Liquidsoap Radio!
##CLI.ICY7#:  channels=2;samplerate=44100;bitrate=24
##CLI.PLAYING#
##CLI.META#:
##CLI.VOL#: 132
##CLI.META#: Руки Вверх! - Убегай

It play well! but only with the patch.
Without it, the vs1053 crash.

If the patch is loaded you see:

VS Version (VS1053 is 4) = 4
SCI_ClockF = 0xB800
I2S Speed: 0
plugin size 18ce 2 c67
plugin start: 7 1 8050 6
scandone

Do a sys.patch ( "1") to enable it again, and reboot.

Are you sure to have the last release? Do an OTA upgrade please.
This is an alpha command not yet documented.

  Are you sure? yes | no

ldv82 wrote 01/31/2017 at 20:26 point
Yes. Already there were rows in the log
plugin size 18ce 2 c67
plugin start: 7 1 8050 6
Tried sys.patch command ( "1") of the sample. Maybe it helped.

What is the difference sys.patch command ( "0") and sys.patch ( "1")?

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 01/31/2017 at 20:42 point

sys.patch ( "0")  inhibe the patch loading at reboot

sys.patch ( "1")  load the patch at reboot.

Some vs1053 doesn't support the patch, so i added this advanced command.

  Are you sure? yes | no

ldv82 wrote 01/30/2017 at 12:21 point

JP cocatrix
Upgrading to version 1.1.5+ via OTA already have? I updated via OTA and just hang on AAC channels began again. And I do not have the firmware 1,1,5, which worked.

It would be nice to be able download the last stable version of firmware.

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 01/30/2017 at 12:38 point

Sorry, i don't understand your request.
AAC Channel?
Send a log please.

I don't want to store old release. Just make the new one working for everybody.

  Are you sure? yes | no

Jean-Pierre Cocatrix wrote 01/30/2017 at 12:55 point

This release adds the official patch for aac. If it is a problem, send

sys.patch("0")

And reboot again.
It seems that some vs1053b are not really up to date to accept this patch.

No mean to see it from the software. (vs version is 4 for all vs1053)

  Are you sure? yes | no

Similar Projects

Does this project spark your interest?

Become a member to follow this project and never miss any updates