Close

90479 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》선릉레깅스룸㉹ベgrace레깅스룸S선릉레깅스룸선릉레깅스е я레깅스룸비용superstition 강남레깅스룸′강남레깅스§8fetch"

  • Z80 (CP/M) Writing to SD Card

  • Digging into SD card writes means shifting gears from the Boot BIOS source code since the Boot BIOS code only does reads. The CP/M BIOS code (CBIOS128.LST) which does the reads/writes after booting. Here's the BIOS code for writes to the SD Card: 0754...
  • We get signal

  • Indeed, immediately after running the Windows software in a VM with the device connected I was getting a live data log of the CO₂ concentration! This screenshot shows me breathing into the vicinity of the sensor:Ok, time to disconnect the device from...
  • Researching Options - Power

  • I'd like to avoid frequently replacing batteries or running power wires to the boxes if at all possible, as such, I'm either wanting to have ultra-low power components and 'smarter' operational times (eg only show LED's when someones in the room) or...
  • Finally, some publicity!

  • An article recently published on MOONGIFT, a Japanese developer site, has showcased RasDash! The article is entirely in Japanese and Google Translate won't accept the URL as it has special characters but YANDEX does. Below are some links and a basic...
  • No officer, it's not a bong. I swear.

  • Morning update: April 13, 89 PDAfter a long night of fighting with 123D make and my 3d printer, we have our first put together. To see very bad pictures of the Main Power/Data Bus (MPDB) look at step 2 of the instructions. After getting put together,...
  • It's like being in college again.

  • Mid-day update: April 20, 89 PDWhile over 75% of the internal parts are finished printing, but there is still too much to do. We have started wiring up the reactor with LEDs but it is slow going (25% done). We have not even started on the code to drive...
  • MORE RADII!!

  • I haven't putzed about with the v0.1 base at all, but I think I've got a motor mount design that I like. It's got the split bolt setup for securing the motor (including a cutout for holding a 2-56 nut), and the legs are cool lofted dealies. Lots of radii...
  • Updated Playground!

  • It's been a minute but there is an exciting new update on Dodo! The original Dodo Playground is a bit long in the tooth and sadly Chrome Applications had been deprecated so there was no longer a good way to flash Dodo games directly from the browser. ...
  • SDWire and SDMux

  • Pleased to discover there are ready to use, non-emulation SD card mux devices available! These are great for 99% of the use cases folks message me about. https://wiki.tizen.org/SDWire SD Wire https://www.tindie.com/products/badgerdnl/sdwire-usb-c-sd-card-reader-sd-mux/...
  • Fibonacci

  • With the ALU verified and the RAM connected, today the breadboard determined that the first 8-bit Fibonacci number is 144. 0000 0000 ld $00 ; outer loop 0001 c200 st [$00] ; a=0 0002 0001 ld $01 ; b=1 0003 fc0a bra $0a 0004 0200 nop ; (pipelining) 0005...
  • Log #89 - CondomBoard specifications

  • Size: about 50x50mm (size of condoms I have, could be a little larger if required)Layers: preferrably a single 2-layer PCB, for easier ordering at the usual suspects in ChinaConnections: debug UARTMicroUSB for charging the batterytemperature sensor connectortwo...
  • 5V, 5W Version Posted

  • I made a 5V, 5W buck derivative that is smaller than the flybuck design but uses the same input/output filter design for low noise/ripple applications. The inductor core is a Magnetics MPP C055048A2. with 38 turns of 24 AWG. Peak efficiency with...