27106 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ《〈 문의 OIO↗5793↗7458 》〉㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ"

Open Indirect Ophthalmoscope
Instructions from Open Indirect Ophthalmoscope
The step by step build instructions for "OIO" can be found here: http://www.instructables.com/id/Open-Indirect-Ophthalmoscope-OIO/

3dPrinted fan control repair
Instructions from 3dPrinted fan control repair
Use a black marker pen and draw a triangle to indicate the switch position if you like. See if you can do a better job with the pen than me.

Mini Potato Cannon
Instructions from Mini Potato Cannon
1.) Cut a hole in the pill bottle just big enough for the pen tube.

Mini Potato Cannon
Instructions from Mini Potato Cannon
3.) Push the hot paperclip through the pen tube about 1/4 inch from the end.

Step 4: Install the Robot - Prepare the Pen-driver
Instructions from Wall Drawing Robot, Open Source
Next step is prepare for pen-driver and put it to robot. Pen holder is up/down by very small stepper motor. The pen-driver base is attached to 1st-layer and 2nd-layer. Those 2 layers is fixed by bolt to keep pen-driver stably.

DIY Vacuum Pickup Tool Part2 - Application Pen
Instructions from DIY Vacuum Pickup Tool

Scratch Pen
Instructions from Scratch Pen
Your scratch pen is ready to scratch the undesired copper from the PCB...

openSip+Puff
Instructions from openSip+Puff
Get an openSip+Puff PCBPCBs and assembled boards will be made available once prototyping is finished and I can find some way to raise the capital needed. For now you can get boards made through OSHPark using the Eagle files supplied, but please contact...

Cloud Pen Drive
Instructions from Cloud Pen Drive
To make your own Cloud Pen Drive, you'll first need to download our repository at https://github.com/rmolines/Smart-Pen-Drive.git and change the main.h file in your src folder to match your host IP and your router's name and password. Then run the node...

Assemble the stylus
Instructions from Stylish!
Take an old pen and clean and hollow it. Get a non sharp, solderable bit of metal to use as the point. I used the tip of a 1/4" plug. Put your holes in your pen for the wire to get to the tip and thread the wire through. Solder the wire to the tip....

Hardware
Instructions from CNC pen plotter
The assembly process is quite straightforward: Assembly the pulleys and pulley holders (3 in total).Assembly the pulleys, the motors and the motor holders (3 in total).Assembly the X shafts and the X shaft holders (2 in total).Assembly the movable left...

Scratch Pen
Instructions from Scratch Pen
Open the cap of lead pen and insert the needle in the cap with the sharp edge pointing outside...

Cut 2 ball point pen springs in half to make 4 springs
Instructions from 3D printed Joystick
If the springs are too strong when the joystick is assembled, cut them a bit shorter.

Frame
Instructions from GRawler - Glass Roof cleaning crawler
Think beforehand how wide the crawler should be, or how wide the lanes are to move along. The length of the profiles and threaded rods depends on that, i use 700mm. Make sure that the profiles dip 1-2mm into the side panels Through the side panels and...

Wiring the matrix (columns)
Instructions from FPGA Blinker
Now, solder 8 wires between C'x and G"x. Calculate the appropriate current limiting resistors values and have them handy (do the calcs and buy them beforehand). Solder the resistors on the borad and use wires to solder the PMOS drains (D'0, ..., D'7)...

1
2
3
4
5
>
>|