2714 Results for "Y 대전 프로토 베팅 CDDC7.COM ▧프로모션번호 B77▧농구경기분석ϧ에스퍼홀덤℁KB손보👢메이저리그라이브중계ӈ대전 프로토 베팅애용 assurable/"

Stick a Fork in it
Log from Novasaur CP/M TTL Retrocomputer
It's done! As in the software is at version 1.0 and ready to ship. _ /o) _/\/\/\_// _/NOVASAUR/ /_/{_}~~{_} Novasaur 64k CP/M vers 2.2 Copyright 1979 (c) by Digital Research a>b:uptime System uptime: 0 days, 03:18:38 CPU Load Average (last 4 mins) 0...

Y Combinator
Log from Our-Watch
After recently receiving the KickBox we have applied for a spot in the Y Combinator accelerator program for the summer of 2016. During this program, you will be flown out to Silicon Valley CA, for three months during the summer. After which they fund...

Y axis
Log from Big Scale Table Plotter

y gantry
Log from OX CNC
putting together the Y/Zi put this on the opposite side by mistake.how much swarf comes out of the delrinright way around, all but one wheel installed.the bottom ridges of the eccentrics are showncompletestarted feeling out the back plate.add the wheelsand...

Y Axis
Log from CNC Plasma Table
The Y axis linear guides do not use the plastic wheels of the original design. They now use rubber coated wheels. The wheels were made from a couple of rollers that were cut down. The ends were faced off to length in the lathe with a center hole opened...

CP/M Disk
Log from My CP/M Single Board Computer
Emulating the new (8085) CP/M I had some problem getting CP/M to emulate with the new version of "cbios". Funny it was working before and "myEcho" is working. A day later I worked out that I had not initialised SOD during the boot process, so printing...

Cabling
Log from STEbus 486DX PC AT Compatible Board
The board does not have the standard D-type connectors for the keyboard, mouse, COM, LPT and VGA ports. There simply isn't room on the 100mm edge.A 50-way header has the COM and LPT ports, which can go to IDC D-type sockets. I'd rather it had been...

Y-axis changes
Log from Axis
I modified length of Y-Axis from 500mm to 600mm, and the machine frame for reflect this change.

Esquemáticos y BOM
Log from Proyecto Robótica I
Se subieron el esquemático en formato PDF y listado de materiales de la placa en formato xlsx en la sección de archivos.

Y axis Motion
Log from 3D Printer

Revamped Y Axis
Log from Actobotics CNC Mill
Worked a little on the Y axis and gantry. I like it! It feels very solid. However, I do need to get the two Y-axis 8mm rods further away from the side channels. Another change is that the Y will be controlled by a stepper outside the main frame, with...

Y-distribution base
Log from 3D printable 125mm butterfly valve
Today I posted a small article about a Y-distributor on Nerdiy.de. With the help of this distributor, a suction support can be distributed over two branches.More Infos here:https://nerdiy.de/en/howto-3d-druck-y-verteiler-fuer-einen-125mm-abluftschlauch-bauen/...

Reconsidering Y Axis
Log from Printrbot 'SuperSize Me" Mod
So the y-axis... I really think it needs to be bigger (surprise!) so, 'Y' not. My reconsideration of leaving the y axis as-is is due in part to heating considerations. The PCB heaters I will be using will be between 8 and 10" square. I am choosing these...

[M] Y Slider
Log from SecSavr Sublime [gd0036]
I think the design of the Y Slider went well. It should do the job of clamping the X axis tubes and look sleek doing it. I made sure that the X tubes were aligned with the Y tubes so that there would be no additional height lost because the X slider...

Repeatability test Y axis
Log from Educational Five-Bar Parallel Robot

1
2
3
4
5
>
>|