Close

1669 Results for "㉣ 피망바둑 ㈍ rka119.top ㅰ 그레잇게임 ㈖ 사설홀덤 ㆌ 포카치는법주소 ㉫ 노리팡바둑이 ㈔ 배터리사이트게임주소 ㈓ 텍사스홀덤추천 ㈚ 맞고게임추천"

  • 1 week left for FLIR Lepton design challenge
  • .Stack entry     by oshpark
  • Submit project ideas by July 21 for FLIR Lepton thermal camera & BeagleBone Blue. Top 5 ideas will receive hardware:https://lepton.flir.com/news-and-updates/new-beaglebone-blue-contest-new-flir-ones/

  • Looking for a 3D-model of the SIZF360
  • .Stack entry     by Christoph
  • These paired FETs have a hilarious package with a top side pad that I'd like to solder to, but I can't find a 3D model. If someone with better 3D skills than me is willing to make one for kicad, that would be awesome.datasheet: https://www.vishay.com/docs/77233/sizf360dt.pdf...

  • Custom Firmware or RIP for HP Laser Printer?
  • .Stack entry     by Designer85
  • I was wondering if it would be possible to make an HP printer (CP5225) print CMY colors, then retract the paper and print the K color on top before exiting the printer? The Uninet iColor 550 and 800 do this (for heat transfers - the 'K' is actually white...

  • Win the Curiosity board!
  • .Stack entry     by Sophi Kravitz
  • Starting tomorrow, 7/22, we'll be running a contest for all brand new Hackaday Prize entries that are using a Microchip part. That means PICs, power chips, op-amps, whatever. We'll be running the Microchip Curiosity contest until midnight PDT (-7:...

  • ESD Concerns
  • .Stack entry     by ZaidPirwani
  • Well, so far I have done a 4 year degree in Electronics and have been using a soldering iron since I was 10 years old... always I have been warned about ESD and protecting my circuits and ICs and stuff, but so far, I have not seen any such problem -...

  • Do P-N junctions oxidize in air?
  • .Stack entry     by Peter Walsh
  • I make sensors by cutting the top off of a metal power transistor and using the base-emitter junction as a PIN diode. This works very well for detecting Alpha particles (and photons).Alphas would be blocked or attenuated by an oxide layer,...

  • Project Idea
  • .Stack entry     by Craig Hissett
  • Just had an idea for a project. It's 1:50am and I'm about to sleep, so just noting here so I don't forget.Bluetooth keyboard, 3D printed wedge like case for it to sit in, with a Pi Zero (w) and an Arduino Mega under. Lcd displays (one for pI, one for...

  • How can I be efficient with my pcb design?

  • .Stack entry     by Simon Merrett
  • I'm designing a pcb to be supported in the slots of an extruded aluminium enclosure, approximately 200mm x 55mm https://imgur.com/TFKDqkU . I need to put parts at either end of the pcb but much of the middle will be unpopulated. Anyone got any top...

  • Glue for 300-400C MCH heater?
  • .Stack entry     by Vitaly
  • I'd like to "improve" MCH heater (50*50*1.5mm) for DIY reflower: add panasonic PGS on top side and aluminium foil on bottom side. That requires glue, operating at least on 300C, ideally up to 400C. Also, this glue should dry without air access and be...

  • Heated Parts of a SLS Printer
  • .Stack entry     by Dominik Meffert
  • At the moment I'm collecting infos for building a SLS 3D printer and I think the most complicated part to build will be the heaters for the powder and the heat resistant chamber. I saw on eg. the Sinterit Lisa that the powder is heated from the top with...

  • My experience with OpenFixture (chat with @morgan)
  • .Stack entry     by Arya
  • <<< - morgan>>> - me <<< Hey bud, you've used Open Fixture before right? what acrylic thickness do you recommend?>>> hey! I don't have any particular recommendations wrt thickness, I used 4mm and was satisfied>>> I also double-cut the "hinge" parts,...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday