Close

6880 Results for "《 예약문의 OIO↗8489↗8306》선릉레깅스┛Еimportanceム강남레깅스룸레깅스룸ㅂheavenly 레깅스룸강남레깅스 강남레깅스룸⊥선릉레깅스ゥfiercelyり"

  • SEGA Megadrive in a FPGA
  • Details     from SEGA Megadrive in a FPGA
  • The ROM images are currently stored in the parallel Flash memory of the board.I plan to add support for SD-Card, and find a way to connect either original pads or USB pads, so it would be possible to actually play games. As it will require some extra...

  • Student AVR board
  • Details     from Student AVR board
  • This page describes a prototype board for the Atmel Mega644 or Mega32 (PDIP) MCU. It includes a power supply, crystal clock, and generous bypass capacitors. A six-pin header allows flash memory programming from an STK500 or AVRISPmkII. All port pins...

  • HD6309 Singleboard Computer
  • Details     from HD6309 Singleboard Computer
  • CPLD glue all written in VHDL and includes CPU clock generation, baud clock generation, address decoding, and SPI master.  A few "registers" were implemented in the CPLD to allow soft-configuration of the SBC.  The address decoder allows the...

  • CANPi
  • Details     from CANPi
  • What is it?Here you'll find the hardware design files for a CAN controller for the Raspberry Pi SBC.It is designed to be easy to use. The CAN transceiver keeps the RPi and the CANPi elctrically isolated, so you do not need to worry about voltage levels....

  • The Quub
  • Details     from The Quub
  • QUUB is an open-source, micro controller system based on a core processor, addressable daughter boards, and remote IO modules. It is a general-purpose embedded microprocessor system, the form factor is based on a main MCU board and multiple stacked...

  • 100w LED projector conversion
  • Details     from 100w LED projector conversion
  • This project started some months back. I was given two projectors, one with a bulb, one without. Not wanting to scrap either unit, equally not wanting to spend £100 on a bulb that would be prone to shock and likely to fail, I decided a more serious...

  • Hakkedpad
  • Details     from Hakkedpad
  • The launchpad is an array of 80 buttons, and 160 LEDs, two per key. It's not touch sensitive, but all the same ... There are five 74HC164, and three 74HC165 inside. 164s (serial to parallel) drive the LEDs, and 165s read the state of the keys. The matrix...

  • hackcase
  • Details     from hackcase
  • case is made from plywood found on the streets. there is some 5mm acrylic too, those i was buying cheap a4 size on ebay. wooden frame is held without glue, mostly little 3mm screws. board are mounted on 5x5cm, 10x10cm, 15x10cm wooden pieces,...

  • T-Board: uc Prototyping
  • Details     from T-Board: uc Prototyping
  • The T-Board was designed with the following in mind: - Speed: Allow microcontroller prototyping on a breadboard, simply and quickly - Ratsnest: Reduce the number of wires needed to prototype with microcontrollers - Power: Allow the project...

  • The FatFingerer
  • Details     from The FatFingerer
  • In the picture of the board, the single DIP switch is wired in parallel with the RUN/PROG switch. This helped during prototyping before I had a case. Also the two tact switches on the DIP area of the protoshield are temporarily the foot switch inputs....
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday