3259 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》선릉레깅스룸㉹ベgrace레깅스룸Ｓ선릉레깅스룸선릉레깅스е я레깅스룸비용superstition 강남레깅스룸′강남레깅스§８fetch"

Make an emu for Enigma Embedded CAS
Details from Make an emu for Enigma Embedded CAS
Box DVB-T2 : VIP : TimboxUse :a- CPU: M88VS3001 b- rom : MXIC MX25L6406E c- ram : hynix H5PS1G63EFR / 8mo d- enigma CAS with caid : 4AD8: 000000 Some Ecm Log 1) 81 70 72 00 90 03 E2 01 C0 E6 24 5A D9 07 D5 40 00 00 00 00...

Grove - Dust Sensor (PPD42NS) Review
Details from Grove - Dust Sensor (PPD42NS) Review
Product Specifications General Type: SensorArchitecture: For ArduinoOutput Signal: Digital (Negative Logic and PWM)Detectable Range of Concentration: 0 ~ 280000 pcs/litre (0 ~ 8000 pcs/0.01cf CF = 283 ml)Detectable particle diameter: >...

HYX file format
Details from HYX file format
This file format was created for my custom, fast, safe, web-centric #SPI Flasher. Data can be translated to/from JSON and raw, with mixed support for block addresses. Other formats must be translated with other software. The file format is best described...

Cheap USB to UART Converter Using MCP2200
Details from Cheap USB to UART Converter Using MCP2200
Nowadays USB port is used widely for data transactions between electronic devices and computers. In many scenarios, there is no need to communicate with the USB port directly, therefore electronic designers use USB to UART (RS232-Serial) converter chips,...

Digital SOS filters for PIC32
Details from Digital SOS filters for PIC32
I decided to start by implementing Butterworth IIR filters using the fixed point formats below. The first step is to find out how much the limited precision arithmetic will affect the filters. I am not using the PIC32 DSP ligrary because I could not...

NEDONAND homebrew computer
Details from NEDONAND homebrew computer
Briefly about architecture and instruction set - it is 8-bit design with 8 registers: 000 - 0 (always zero) 001 - A (accumulator) 010 - B 011 - C 100 - D 101 - E 110 - F (flags and 3 higher bits for jumps) 111 - G (8 lower bits of program counter) Flags...

MorphESP240 - ESP32S2 DEV board
Details from MorphESP240 - ESP32S2 DEV board
A powerfull dev board with the ESPRESSIF™ ESP32-S2®, a high resolution display, a RGB LED, a battery charger and a bunch of GPIOs. There are many ESP32 board on the market but very few with the new ESP32-S2 which handles USB communications, new...

REDACTED - The First Fully Open Bipedal Robot
Details from REDACTED - The First Fully Open Bipedal Robot
Project choices and the mission As stated in the summary, my goal is to provide an open solution to the bipedal walking problem, in order to give others a starting point and source of inspiration. This includes hardware designs, drawings, assembly plans,...

Ameise
Details from Ameise
A clock built with eight authentic soviet vacuum fluorescent display (VFD) tubes, a custom designed circuit board, firmware and 3d-printed case It is an evolution of Phalanx. Many of the firmware improvements made for Ameise also trickled down to Phalanx...

Technogym : new Heart Rate BLE sensor
Details from Technogym : new Heart Rate BLE sensor
The Technogym manual indicates that the RF HR receiver outputs a 5V and 30 ms pulse for each heart beat. A ESP32 with abilities will be the perfect µc. It's a easy job for it to read the incoming HR value and to output a pulse. Since the ESP32 works...

Arduino Variable Speed Temp. Fan Controller
Details from Arduino Variable Speed Temp. Fan Controller
You can find the schematic ready to edit and go on EasyEDA here. Source code for the Arduino sketch is attached and below. Note that it uses the TimerOne library to provide higher-resolution Timer1 frequency control for the Pulse Width Modulation to...

Monitoring-Temp-and-Humidity-using-AWS-ESP32
Details from Monitoring-Temp-and-Humidity-using-AWS-ESP32
HARDWAREESP-32: The ESP32 makes it easy to use the Arduino IDE and the Arduino Wire Language for IoT applications. This ESp32 IoT Module combines Wi-Fi, Bluetooth, and Bluetooth BLE for a variety of diverse applications. This module comes fully-equipped...

Stranger Board
Details from Stranger Board
The project is wholly composed by off the shelf components: ESP-01ArduinoDS3231 RTCNeoPixels5V to 3V3 regulator The ESP-01 creates a hotspot and serves a page with a form and a button The Make it Glow button maskes the ESP01 send the string typed ...

How To Build A FlameWheel Robot (A Remote Control
Details from How To Build A FlameWheel Robot (A Remote Control
Today we present the FlameWheel Robot assembly tutorial and quick-start guide! It is rather difficult to assemble this robot without guidance. Feel free to refer to my introductory tutorial today.Flamewheel (A 2WD Remote Control Robot) is part of our...

BARCO NX-4 GROUP REVERSING ADVENTURE
Details from BARCO NX-4 GROUP REVERSING ADVENTURE
The story so far... Update: Row scanning working.Known/working: Building and loading via JTAG new firmware into the main FPGA. This firmware is starting from scratch, we don't understand much yet about the default Barco firmware, although we've dumped...

1
2
3
4
5
>
>|