72 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》선릉레깅스룸㉹ベgrace레깅스룸Ｓ선릉레깅스룸선릉레깅스е я레깅스룸비용superstition 강남레깅스룸′강남레깅스§８fetch"

Arduino Variable Speed Temp. Fan Controller
Details from Arduino Variable Speed Temp. Fan Controller
You can find the schematic ready to edit and go on EasyEDA here. Source code for the Arduino sketch is attached and below. Note that it uses the TimerOne library to provide higher-resolution Timer1 frequency control for the Pulse Width Modulation to...

Making a solder mask using Kapton tape
Details from Making a solder mask using Kapton tape
One-Off Solder Mask This document outlines how to take an EAGLE layout, a printed circuit board manufactured using the Protomat C60 circuit board cutter, Kapton tape (1 mil thick), and a Universal Laser VLS 3.50 to create a solder mask for your circuit...

Flex Modules
Details from Flex Modules
The general goal is to make a 'kit' of reusable components for wearables.Bluetooth BLE is the standard for communications. WiFi, etc. require too much power and anyone with a wearable likely has an Android or iOS phone. All wired connections are USB...

Toner Transfer with Kapton
Details from Toner Transfer with Kapton
Stop buying expensive toner transfer paper and instead make custom transfer sheets with Kapton tape! This project is one of many I have written into my latest book, The Makerspace Workbench. Enjoy!

NoteOn Smartpen
Details from NoteOn Smartpen
The goal of the NoteOn project is to create a smart pen that is better than the ones currently on the market. It should be small, wireless, and self-contained.Small: Most smart pens are 12mm or more in diameter. Normal writing implements generally range...

anaButtons
Details from anaButtons
Very Brief Overview:The AVR's digital inputs are Schmitt-Triggered, allowing for slowly rising/falling and/or noisy "edges" to be "cleaned up" into sharp 0->1 or 1->0 transitions. The threshold-voltages for each transition differ, but are quite stable,...

Shop Air Injection Molder
Details from Shop Air Injection Molder
The HeaterThe heater design is based on this machine.120v400W~3.33AThe heater unit will be 6" long and 1/2" OD. It will be heated by Nichrome wire ~95" long to provide approx 10 turns of wire per inch of heater. Using a calculator I have come up with...

Magnificent Magnifier LED Coversion
Details from Magnificent Magnifier LED Coversion
I used these bulbs:http://www.amazon.com/Light-Bulbs-Equivalent-Halogen-Bi-Pin/dp/B00NTTJCZSI now have half a dozen in different fixtures and have been very happy so far - good price ($2.50 ea. in the six pack), nice light output, and good build quality....

Packaging DESIGNED for ReUse as components
Details from Packaging DESIGNED for ReUse as components
So far I have focused on the development of domestic renewable energy generation equipment that is currently considered by most to be uneconomic due to it's high capital cost and lengthy payback periods. Now that most government subsidies have been removed,...

3D Printer Heated Bed Insulation Mod
Details from 3D Printer Heated Bed Insulation Mod
Notes on the Instructable Guide:Step 1: We found that we couldn't reach 110° C or even maintain 95° C with any sort of stability with our cardboard and aluminized mylar backed foam homemade thermal isolation. Without any thermal isolation (as...

Warlock costume – Staff & invisibility cloak
Details from Warlock costume – Staff & invisibility cloak
The staffEvery warlock has a staff and this staff is packed with goodies – soft lights, high lights, fairy lights and cloak color and pattern control that is being done by a lot of software, electronics and wireless modules – very useful lights for the...

Nitinol Addams Family 'Thing' hand
Details from Nitinol Addams Family 'Thing' hand
The original flexinol hand kit uses a 555 timer to slowly control each finger sequentially.I replace the 555 timer pcb with a relay board connected to a MIDI interface PCB with dreamblaster X1 module. This picture gives an overview of the setup :The...

Carbon tape heated gloves
Details from Carbon tape heated gloves
Apply a small amount of rubber cement to a small area of the carbon ribbon (just for one finger). You do not have to apply the adhesive on a large length of the tape. You will be easier to stick a small portion of the tape, one finger after another,...

Hourglass Clock
Details from Hourglass Clock
When I finished the clock I put together a quick video describing the clock. There wasn't any video to speak of that was taken during construction though there were a bunch of pictures. This details section walks through many of the steps that were taken...

Heated Bed for M3D 3d Printer
Details from Heated Bed for M3D 3d Printer
Heated Bed for M3DI made this project as a heated bed is the most reliable way of printing ABS models with extruding 3d printers. ABS is less brittle than PLA and a bit more heat resistant. M3D printer comes with a very impressive price of 350$ but also...

1
2
3
4
5
>
>|