3-11-2024 See these two 2011 Liliputing and TechCrunch articles, which were partly the inspiration for this project: https://liliputing.com/pixel-qi-suggests-low-power-tablets-could-be-powered-by-1w-solar-panels/(6-3-11) https://techcrunch.com/2011/06/04/first-solar-powered-laptop/ (6-4-11)...
The selection of the feedback resistors is critical. The standard output voltage is supposed to be 3.3V. For the appropriate resistor values i just checked the datasheet which had a table with values. Since the I want to be able to select the output...
UPDATE 02/11/2017Previously mentioned bugs pertained to lots of noise while playing video streams. This was almost completely resolved by slowing down SPI to 8Mhz and increasing frame rate to 40. Another final part may be driving 5v SPI leds with a 3.3v...
From OpenCores PDP-8 page: Features In this FPGA implementation, the PDP-8 CPU can be configured to emulate the instruction execution of a PDP-8 (Straight-8), PDP-8/S, PDP-8/S, PDP-8/I, PDP-8/L, PDP-8/E/F/M, PDP-8/A, HD-6100, or a HD-6120. The...
You can use the ESP32 simulator on Linux, Windows or even Chromebooks! The project runs on the browser. So, you can always run the projects on mobile as well! There are several users using the ESP32 simulator on their MacOS as well! The connection diagram...
The internet has a dizzying amount of information on EC and pH. After sifting through it, I found some potentially interesting links that are detailed below. The DIY EC meter project that inspired the original EC portion of this design A tutorial on...
As low-cost desktop 3D printing is now dominated by free and open source self-replicating rapid prototype (RepRap) derivatives, there is an intense interest in extending the scope of potential applications to manufacturing. This study describes a manufacturing...
Note: This project assumes you have Arduino IDE setup and know how to connect and write to an Arduino Uno board. Hook Up Your Servos The first step is to hook up your servos to your UNO. If you purchased the same servos I used from Amazon the wires...
The team Digitabulum is Manuvr's flagship project. Here is out team. Ian Lindsay started the project in 2014, and is the hardware designer and low-level bit-pusher. Brent Long builds 3D augmented-reality applications. Josh Treadwell is an electronic...
500W Power Inverter With Reverse Polarity Protection Hi friends. I have TG500 UPS but it have some problem so, i use it's transformer, mosfet,diode,capacitor for make new Inveter. I hope you like it. In video below i show you how to make 500w...
This board is part of Fyber Labs Flex Module project.Flex sensor input to ADC will be essentially DC voltage so filtering isn't critical. The buffer provides uniform impedance and somewhat linear use of the 0-3.3V ADC input for the resistance range of...
Hardware:The hardware is not very complexe if you're familiar with Raspberry Pi. The screen is a recycled one from office, a standard 19" DVI. The resolution is 1280x1024. It's rotated in portrait mode.The printer is an Epson TM-T20II, connected to the...
1. Cel: Celem pracy jest wykonanie projektu urządzenia mechatronicznego lub kluczowego elementu urządzenia mechatronicznego, zbudowanego na bazie podzespołów LEGO oraz przeprowadzenie procesu projektowego zgodnego z rzeczywiście używanym...
The effect circuit works this way: A high input impedance buffer amp (T1, T2) receives the signal, which is then split in two ways: it is fed directly to one of the inputs of the mixer amp (IC1-A), and is fed into a high-pass Sallen-Key filter (T3),...
This board is part of Fyber Labs Flex Module project.Biopotential signals are low frequency small voltage output that need very clean power and low cross-talk routing.Example signal types(source): EEG:Surface 5 mV 200HzScalp 300uV 100HzEMG:On skin 10...