Results for %E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%E3%86%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%85%94%EC%B8%A0%EB%A3%B8applause%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EC%8B%A0%EC%82%AC%EC%95%84%EC%9D%B4%EB%A6%B0%EC%A3%BC%EB%8C%80caught %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%E3%8F%87%E3%85%97%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0queer

Program the Microcontroller
Instructions from Fear the Scary Cat!
Before mounting the prototype PCB to the housing, I recommend uploading the required sketch to the ATtiny84 microcontroller with a programmer of your choice. I used a USBtinyISP type shown in the picture. /*Sketch for the Scary Cat Project by Gene H*/...

Hacking a MG92b : Protect control bard
Instructions from Smarter Micro Servo (SMS) MOD
Use a a piece of heat-shrink sleeve as an envelop, or print a small 3D case to protect the control board.

Step 5: Uploading Arduino Codes & Conclusion
Instructions from Spider Robot with Arduino
We have prepared a code for you so that you can move the spider robot without any problems at first. A few commands are ready in the code, but you can revise it yourself ;#include // include IR Remote library #include // include servo library //=====...

▇▇▇▇ Understand Synchronous Logic ▇▇▇▇
Instructions from FPGA Bootcamp #2
Clocks are an important part of practical digital design. Suppose you have a two input AND gate. Then imagine both inputs go from zero to one, which should take the output from zero to one, also. On paper, that seems reasonable, but in real...

▇▇▇▇ Code Solution ▇▇▇▇
Instructions from FPGA Boot Camp #4: State Machines
There are many possible solutions, of course, but here's mine. Let's break it down into manageable pieces. First, let's look at the housekeeping items. I mentioned a 12 MHz clock, although that's ugly for simulation. Because of that, I wrote two...

NODE-RED CONNECTIONS!
Instructions from OBS_IRL_STREAM_DECK
The first thing we need is a basic flow to separate button presses into different outputs. [{"id":"50b49ab2.1e6f64","type":"mqtt in","z":"7805686.aa4fd98","name":"","topic":"button_glove","qos":"0","datatype":"auto","broker":"","x":310,"y":2180,"wires":[["ea9f502f.2dd17"]]},{"id":"ea9f502f.2dd17","type":"json","z":"7805686.aa4fd98","name":"","property":"payload","action":"obj","pretty":false,"x":490,"y":2180,"wires":[["425aef92.aa3da8"]]},{"id":"425aef92.aa3da8","type":"function","z":"7805686.aa4fd98","name":"ButtonSeperator","func":"var...

▇▇▇▇ Understanding Basic Logic Gates ▇▇▇▇
Instructions from FPGA Bootcamp #0
Open the simulator using this link and you'll see the three fundamental logic gates that will build up just about all kinds of logic. To the left are two logic inputs and each gate has its own output. Remember, you can click on the inputs to change from...

Configure LoRa device
Instructions from Soil moisture sensor with LoRa
In HTerm or any other terminal program you see the start of the module after plugging the power supply jumper.Now you can configure the SMT100 by entering the password in HTerm (123456) and then send AT commands (Attention: Always capitalize commands...

Front end assembly
Instructions from OSUG: Open-Source Underwater Glider
Place a single 608ZZ bearing in each of “Syringe_clamp_front” and “Syringe_clamp_back” On the “Syringe_clamp_back” secure the bearing in place with the “Engine_bearing_fastener” piece, 3 M3 20mm...

rDUINOScope Boiana
Instructions from rDUINOScope Boiana
TEP 3 AssembleFor more detailed instructions, please visit the Project Website : http://rduinoscope.co.nf/rDUINO_step3.htmlNow is the time to create the Shield board. A Shield board is a board with pinouts which you stack on top of the ArduinoDUE board.Some...

Main Wiring
Instructions from Capacitive Gamepad
Connect MPR121 to arudino i2c and power. On a Micro this is pins 2&3 plus VCC and GND. Flash the arduino and make sure everything works as you like. Breaking out the RST pin to a tactile switch is probably unnecessary, i've had no problem re-flashing...

▇▇▇▇ D Flip Flops ▇▇▇▇
Instructions from FPGA Bootcamp #0
The SR latch modified with the inverter is often called a D latch because the single input is data for the latch to store. To make it a D flip flop, though, you need to arrange to capture the data at a clock edge, not just any time the latch is enabled....

Wiring the Circuit
Instructions from The Wireless Tin Can Telephone
Once everything is securely glued in, it’s time for wiring! Use the provided schematic to connect all the jumpers to their appropriate pins. I’ll also provide the pin-outs below: (Note, this is for the Gravity Expansion HAT) Antenna Board: MI -> MISOMO...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
I attached a 2 axis gyroscope and 3 axis accelerometer onto this project so that I could add some interesting control to the device. The 5 degrees of freedom board from Sparkfun outputs data from its gyroscope and accelerometer as analog voltages. I...

Circuit Connection:
Instructions from DIY Arduino Tic Toc Toe Game
Connect the push buttons keypad to Arduino Uno as shown in circuit diagram.(R1~A0,R2~A1,R3~A2,R4~A3,C1~A4,C2~A5,C3~Pin 2,C4~Pin 3).Also take a extra push button(Reset Button) and connect to Arduino.(Reset,GND).Connect all the pixel LEDs.(-Ve/GND~GND,+Ve/5V~5V,Data...