13109 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

Hardware requirements
Instructions from Building Visitor Management System - Waylay IO
For this tutorial, we have decided to use the M5Stack Ecosystem because it enables building such a system without prototyping specific tools, such as a soldering iron or prototyping cables. The brain of this project is the M5Core2, an IoT development...

Step 6: Demonstration
Instructions from Telescoping Pole Extension Sensing - Photoresistor
To demonstrate that the calibration was successful, we recorded a video and collected photoresistor readings while arbitrarily extending, retracting, and twisting the telescoping pole. The plot shares the output from the two photoresistors over time....

Wire Connections
Instructions from Building Visitor Management System - Waylay IO
Connect the Mini RFID Reader/Writer Unit to PORT A of the M5Core2 (the red port near the USB-C connector) using the Grove cable. This unit uses the I2C protocol to send data to the M5Core2.Take out the CORE2 plate on the back to expose the pins.The Finger...

Setting up Ameba to be I2C Master
Instructions from Communicate with Arduino UNO via I2C
Next, open another window of Arduino IDE, make sure to choose your Ameba development board in the IDE: “Tools” -> “Board”Then open the “Master Writer” example in “File” -> “Examples”...

Demonstration
Instructions from Strain Gauge Force Vector Sensing Pole
Turn on the Arduino recording and output, and collect the readings of interest from the strain gauges. In this example, we pressed the tip of the telescoping pole against a pumpkin on a chair to demonstrate the sensing principle. The force and direction...

Step 5: Demonstration
Instructions from EMT Conduit-Mounted Wind Sensors
The wind sensors, Arduino and EMT conduit telescoping mounting pole took measurements outdoors for about 90 seconds. The raw data, and processed wind speed and wind direction data are presented below. The method for converting from the raw Arduino readings...

Setting up Arduino Uno to be I2C Slave
Instructions from Communicate with Arduino UNO via I2C
In this example, we use Ameba as the I2C master writer, and use Arduino as the I2C slave receiver.When the I2C slave receives string sent from I2C master, it prints the received string. Setting up Arduino Uno to be I2C Slave First, select Arduino in...

Motion Alerts From Anywhere in the World
Instructions from Motion Alerts From Anywhere in the World
In this example, instead of adding a Digital Pin Writer Node, we are going to add an Interrupt Pin Reader Node. As the name suggests, this will monitor the signal pin on the PIR motion sensor and send the state on the Node's output pin. In this case,...

Prepare the disks and write the image to media
Instructions from pfSense Router/Firewall Install
I'm going to be using two USB sticks for the install process: the first is the pfSense installer and the second is the boot drive onto which pfSense will be installed. But before that, you'll need to decompress the image you downloaded. The following...

All of the steps for the project!
Instructions from Air Pollution Monitoring Project
Let’s get to it! Install Arduino IDE, the esp32 board and the Fixed Libraries. To install the ESP32 board in your Arduino IDE, follow these next instructions: 1) Open the preferences window from the Arduino IDE. Go to File> Preferences 2) Enter https://dl.espressif.com/dl/package_esp32_index.json into...

Code
Instructions from ESP32 Personal Bat Signals with Light and Sound
I used micropython, because I haven't used it for a project yet and I was shocked how well it worked for this. There are many tutorials on how to use Thonny with an ESP32, and I found it to be much quicker than doing this in Arduino/ C++. The main files...

Hummingbird
Instructions from Hummingbird
Step 3: Connect to VivaPlanetThis next step is a bit more complex and requires some C# and visual studio with the Gagetter software from GHI Installed. This will take some time...persist it will be worth it in the end...There are a lot of great tutorials...

Breathing Detection
Instructions from Breathing Detection
Labview and Arduino IntroductionLabVIEW (short for Laboratory Virtual Instrument Engineering Workbench) is a system-design platform and development environment for a visual programming language from National Instruments.To learn about LabView check official...

TI-84+ SE Backlight
Instructions from TI-84+ SE Backlight
On the back of the LCD there is a reflector and a polarizer. This diagram shows the different layers.The reflector is a thin foil sheet on back of the polarizer. It needs to be removed so the backlight can shine through. The polarizer is a thicker plastic...

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
First buy an HP Touchpad and a Touchstone Inductive Charging Dock (about $200 for both).

1
2
3
4
5
>
>|