Results for 《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ《〈 문의 OIO↗5793↗7458 》〉㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ

Final Assembly:
Instructions from THB6064AH-SMT Stepper Motor driver
12. [ ] The big THB6064AH chip: Since this product has a MOS structure, it is sensitive to electrostatic discharge. These ICs are highly sensitive to electrostatic discharge. When handling them, please be careful of electrostatic discharge,...

Low Cost CO2 Laser Build
Instructions from Low Cost CO2 Laser Build
Mirror Mounts0Mirror Mounts… where to begin, in many ways… these are the make or break it for this project. These have some very high tolerances and requirments. Especially considering I am doing this all by hand, after all, the goal of this project...

ramanPi - Raman Spectrometer
Instructions from ramanPi - Raman Spectrometer
Section: 1A completed TFT LCD and Touch Panel DisplayComponents Required: Printed versions of the following 3D Printed Objects from the gitHub respository: (1x) trim_tftFaceplate_keypad-display(1x) trim_tftFaceplate_facia(1x) Cube beam splitter...

Lexitron RSS Reader
Instructions from Lexitron RSS Reader
Lexitron circuit design and hardware:LED display: The display is constructed using Red 8x8 square LED matrix displays, each containing 64 LEDs wired in a square grid with the 16 column and row pins available out the base. It is designed to be used in...

Lexitron RSS Reader
Instructions from Lexitron RSS Reader
Tickernut circuit design and hardware:Enclosure:The motherboard is shaped to fit tightly inside a standard ABS jiffy box which set its limited size. The box has cutouts to expose all motherboard connectors on the left side and a small speaker and antenna...

Lexitron RSS Reader
Instructions from Lexitron RSS Reader
Tickernut construction log:Construction was completed in stages over the period of many months with a design that evolved to suit the available parts. The progression of construction was arranged so that each stage could be completed and tested...

Fan controller for Re:Load Pro
Instructions from Fan controller for Re:Load Pro
Find 3 thin wires for the fan and test that it can get through the small hole in the heat sink, and solder them to the PCB.Now it is time to solder the PCB to the expansion slot.Glue the temperature sensor to the heat sink and get the 3 fan wires through...

Digital Bench Power Supply
Instructions from Digital Bench Power Supply
Find a heatsink for the transistors. Mount them there, including the emitter current equalising resistors. Mount the entire assembly on your project's enclosure

ESP8266 WIFI Mains Power Dimmer / Switch
Instructions from ESP8266 WIFI Mains Power Dimmer / Switch
Don't forget about the Heatsink for your Triac. If you stay, and mostly of you will stay, under 50-80W then probably will be no big need. Check carefully your Triac datasheet and adjust accordingly with your needs. The one in the picture beloow is just...

Teensy v3.1 - FrSky S.Port & WS28xx Led Shield
Instructions from Teensy v3.1 - FrSky S.Port & WS28xx Led Shield
The led holders used in my video: https://www.thingiverse.com/make:103857Source files: https://www.thingiverse.com/thing:300588and the leds used for them:http://www.ebay.ca/itm/171527714203Wire Used for the leds (6p super flexable):http://www.goodluckbuy.com/6p-6-pin-silicone-wire-data-cable-brushless-gimbal-camera-mount-sensor-motor-gps-fpv-1m.html...

Butterfly PI - Maker Version of a Security Cam
Instructions from Butterfly PI - Maker Version of a Security Cam
Build a personal live streaming camera with Raspberry PI to watch on mobileToday, we are going to let Raspberry PI turn into a remote security cam that we can control and watch live anywhere on the planet with using our mobile phone. This is the maker...

XBox 360 Extra Cooling Fan (anti-RROD)
Instructions from XBox 360 Extra Cooling Fan (anti-RROD)
Solder pin header to board (I only used 2 pins for VCC and GND).I had to remove the smaller heatsink to get better access to the solder points.

DIY Yag Laser
Instructions from DIY Yag Laser
This is one of the led modules I am using.I have modified it to remove the ears and the corner tabs.I will be using the connection inside the module.Here the 9 modules are mounted on the heatsink. I used 1" stainless No. 4X40 the extra length will assist...

Hacking PTC Heater for SMD Soldering
Instructions from Hacking PTC Heater for SMD Soldering
Find or build a suitable stand for your PTC heater; unless you have a high temperature surface it should be offset. I used an old heatsink from the Pentium II era. Be creative.

Hacking PTC Heater for SMD Soldering
Instructions from Hacking PTC Heater for SMD Soldering
Secure the PTC heater to the heatsink. My initial test ignored this step, but I strongly recommend it for safety reasons.

57 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ 《〈 문의 OIO↗5793↗7458 》〉 ㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ"