121 Results for "%EA%B0%95%EB%82%A8%EC%98%A4%ED%94%BC%EC%9D%B4%EB%B2%A4%ED%8A%B8%E2%86%B2optime4%E3%80%82com%EA%B0%95%EB%82%A8%EC%98%A4%ED%94%BC %EA%B0%95%EB%82%A8%EB%A7%88%EC%82%AC%EC%A7%80 %E2%86%B2 %EA%B0%95%EB%82%A8%EC%98%A4%ED%94%BC%E1%98%AE %EA%B0%95%EB%82%A8%EC%98%A4%ED%94%BC%EC%83%9D%EA%B0%81%E1%98%AE %EA%B0%95%EB%82%A8%ED%9C%B4%EA%B2%8C%ED%85%94 %EA%B0%95%EB%82%A8%ED%82%A4%EC%8A%A4%EB%B0%A9 %ED%83%80%EC%9E%84"

D.I.M.E.R PROJECT 6 DOF Robot Arm
Instructions from D.I.M.E.R PROJECT 6 DOF Robot Arm
Hello there!In Christmas I had a little more time to improve DIMER, improvements have been mainly two; motor drivers and two potentiometers to know their position and power programming.Drivers:In Bilbao maker fair another maker told me he had just found...

▇▇▇▇ State Implementation ▇▇▇▇
Instructions from FPGA Boot Camp #4: State Machines
When creating a state machine, there are two things to consider: How to represent the state you are currently in is the most obvious one. This may seem like a trivial concern, but as you'll see, there is more to it than meets the eye. The second decision...

▇▇▇▇ Add Constraints ▇▇▇▇
Instructions from FPGA Bootcamp #3
Assuming your toolchain knows about the specific FPGA you are using, you might think you only need to feed it Verilog (this is analogous to a C compiler that knows about your CPU only needs C source code). However, there is one piece we didn't have to...

Coil Gun
Instructions from Coil Gun
Step 1 – Preparing the coils (DIY make coil gun without camera) Making the...

rDUINOScope Boiana
Instructions from rDUINOScope Boiana
TEP 3 AssembleFor more detailed instructions, please visit the Project Website : http://rduinoscope.co.nf/rDUINO_step3.htmlNow is the time to create the Shield board. A Shield board is a board with pinouts which you stack on top of the ArduinoDUE board.Some...

3D Printing
Instructions from Joy Robot (Robô da Alegria) 2017 edition
The robot structure was entirely produced with 3D printing using Autodesk Fusion 360. In order to enable the production of robot replicas in makerspaces or fab labs, where the maximum time of use of the printers is crucial, the design of the robot was...

Raspberry Pi Zero Smart Glass
Instructions from Raspberry Pi Zero Smart Glass
On The Raspberry Pi Zero in Terminal and type these commands to install theRTL8723BU Wifi+Bluetooth 4.0 module (should take about 1 hour to compile)First Lets install the Wifi driverspi@raspberrypi:~ $ sudo apt-get install raspberrypi-kernel-headers...

Tools and Materials
Instructions from Joy Robot (Robô da Alegria) 2017 edition
The following tools and materials were used for this project: Tools: 3D printer - The whole body of the robot is 3D printed. Several hours of 3d printing were needed for building the whole structure;PLA filament - White and black PLA filaments...

Tools and Materials
Instructions from DIY Wi-Fi Smart Scale (with ESP8266)
The following tools and materials were used in this project: Tools and materials: 3D printer (link). It was used for printing the case where the electronics are encloused.Solder iron and wire. Some of the components (ESP8266 Firebeetle and...

Tools and Materials
Instructions from DIY Smart Scale With Alarm Clock
The following tools and materials were used in this project: Tools and materials: 3D printer (link / link). It was used for printing the case where the electronics are encloused. Solder iron and wire. Some of the components (ESP8266 Firebeetle and LED...

Front end assembly
Instructions from OSUG: Open-Source Underwater Glider
Place a single 608ZZ bearing in each of “Syringe_clamp_front” and “Syringe_clamp_back” On the “Syringe_clamp_back” secure the bearing in place with the “Engine_bearing_fastener” piece, 3 M3 20mm...

Raspberry Pi Zero Prism
Instructions from Raspberry Pi Zero Prism
On The Raspberry Pi Zero in Terminal and type these commands to install theRTL8723BU Wifi+Bluetooth 4.0 module (should take about 1 hour to compile)First Lets install the Wifi driverspi@raspberrypi:~ $ sudo apt-get install raspberrypi-kernel-headers...

Prepare the CNC Files
Instructions from EnLIGHTen Web-Connected, OPEN source, LED Clock
The construction work of the CNC machine is pressing go on your CNC machine. But as anyone knows, CNC work is 95% setup and 5% cutting! A few words on setup are important here. First, getting a solid fixture is essential. I am choosing to hold down the...

Code for single Esp32 Board
Instructions from Bluetooth Tracker
This is the code for everything on a single Esp32 Board. Since I didn't have the correct board, I needed to use two of them, and they communicate through the serial port.The Bluetooth packets address and raw data get printed to the Arduino Serial...

The Talking Microtronic Computer System Emulator
Instructions from The Talking Microtronic Computer System Emulator
Set up the hardware - the emulator main sketch shows the pin layout: // // SD+Ethernet Shield (optional) // #if defined (SDCARD) #define SDCARD_CHIP_SELECT 4 // // software serial interface for Emic 2 TTS module (optional) // #if defined (SPEECH) #define...

|<
<
1
2
3
4
5
>
>|