102 Results for "㉣ 피망바둑 ㈍ rka119.top ㅰ 그레잇게임 ㈖ 사설홀덤 ㆌ 포카치는법주소 ㉫ 노리팡바둑이 ㈔ 배터리사이트게임주소 ㈓ 텍사스홀덤추천 ㈚ 맞고게임추천"

Simple Edison Breakout Board
Instructions from Simple Edison Breakout Board
Simple UART level converter.As I'm sure you are aware, the Edison is 1.8v gpio only so you either need to get a 1.8v TTL USB Cable or you can use a 3.3v or 5v Arduino style TTL USB cable, but it will need a shift level to achieve this.So a simple design...

Sub $200 PCB Mill that doesn't suck!
Instructions from Sub $200 PCB Mill that doesn't suck!
Wiring up the relay for the spindle:The relay needs 5V because it wants I/O TTL level for switching. You can use D9 which controls the RAMS 1.4 extruder fan usually BUT you need to wire the relay directly to the D9 pin. It is located on the top row on...

Post-hoc analysis
Instructions from PhotometryBox
Unzip analysis scripts from "Post-hoc analysis scripts Matlab 20190426.zip"Add scripts to Matlab pathOpen the script fibPhotDemo.mSet the frequency ranges for each channel by adjusting the variables params.freqRange1 and params.freqRange2 at the top...

Step 37 – Solder connectors to the RS485 Module and mount module inside the enclosure
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
First, remove any sockets that are present on the RS485 Module as we need as much free space as possible. Solder a black wire between TTL Ground and RS485 Earth. Solder 4-core cable to the left (TTL signals) side of the module and at the opposite end...

BOB PID Servo Controller
Instructions from BOB PID Servo Controller
J2Pin Signal from BOB PCBPIC PIN1+5 Logic power (if needed)VCC2CTS (unused)RB43GroundGND4TX USB/HostRB7Serial Console: To talk to the controller via USB - TTL serial (Required to set the PID constants):[ ] Install J2 RLC header on the top side for USB...

Instructions:
Instructions from Laser XY Scanner
Step 1: Gather Your Components Laser XY Scanner - BOM I usually like to source my parts from DigiKey, but the low-cost options on Amazon are hard to beat sometimes. This list is just one of many sources for each component in the BOM. There are of...

STEP 3: Configuring your serial ports and ssh
Instructions from PR-Holonet: Disaster Area Emergency Comms
Back to top Follow the instructions HERE to get to the the Raspberry Pi Configuration panel. Navigate to the Interfaces tab. Make sure that the following interfaces are SET ENABLED InterfaceSettingSSHENABLEDSerialENABLED DISABLE the serial...

ESP8266 Retro Browser
Instructions from ESP8266 Retro Browser
Getting Starting - Changes to the Seeed Tutorial After a 3 or 4 week wait, your ESP8266 Serial Wifi modules have finally arrived from China. Now what? For a first program, most people head for the short tutorial at seeedstudios http://www.seeedstudio.com/wiki/WiFi_Serial_Transc......

Camera Interfacing
Instructions from Raspberry Pi Zero W V1.3 Development Board
The key feature of the of the Raspberry Pi Zero W V1.3 was to support camera serial interface (CSI connector) which used to be equipped on high end Raspberry Pi. Thus, Pi Zero w began to be able to connect with cameras. Indeed, numerous Raspberry Pi...

Configuring KNXD
Instructions from KNX Raspberry Pi HAT
Before we can start configuring OpenHAB and create our KNX network, we need to set up KNXD. It has to be configured to start automatically at boot as a service and it needs to be given the right arguments to communicate with the Raspberry Pi HAT. Before...

ramanPi - Raman Spectrometer
Instructions from ramanPi - Raman Spectrometer
Section: 5A complete Laser Emitter AssemblyComponents Required: Printed versions of the following 3D Printed Objects from the gitHub repository: (1x) electronic_mount_laser_bottom(1x) electronic_mount_laser_top(1x) 532nm 150mw Green...

Portable travel NAS
Instructions from Portable travel NAS
Let's get cracking, get the Carambola up and running. I like to connect to the serial terminal, the development board features a usb ftdi chip allowing me to use a terminal program like PuTTy to connect.Connecting to serial terminalFirst step: see that...

Infinity Mirror Clock
Instructions from Infinity Mirror Clock
Electronics: A Standalone Arduino: http://dushyant.ahuja.ws/2013/10/standalone-arduin...OR Arduino mini pro: http://www.aliexpress.com/item/10Pcs-Lot-Pro-Mini-...RTC Module – DS1302: http://fabtolab.com/DS1302-RTC-module?search=rtcLM2596 Step Down Adjustable...

Reviving tossed stepper motors
Instructions from Reviving tossed stepper motors
Now that we know what kind of stepper motor we have, we can build a simple test circuit to get the thing moving. At the bottom left, the control pins for the motor can be connected to any TTL logic device you wish to use to run the motor (in my project...

Reviving tossed stepper motors
Instructions from Reviving tossed stepper motors
Next we have to set up the control software to drive the motor. Each of the motor phases should be connected to a pin of your TTL control device such as a GPIO pin on an Arduino Uno. In order to turn the motor in either direction, we have to turn on...

1
2
3
4
5
>
>|