185 Results for "%EB%8C%80%EA%B5%AC%EC%98%A4%ED%94%BC%EA%B0%95%EC%B6%94%E2%86%B2www%2Coptime4.com%EB%8C%80%EA%B5%AC%EC%98%A4%ED%94%BC%20%EB%8C%80%EA%B5%AC%EB%A7%88%EC%82%AC%EC%A7%80%20%E2%86%B2%20%EB%8C%80%EA%B5%AC%EC%98%A4%ED%94%BC%E1%99%97%20%EB%8C%80%EA%B5%AC%EC%98%A4%ED%94%BC%EC%83%9D%EA%B0%81%E1%99%97%20%EB%8C%80%EA%B5%AC%ED%9C%B4%EA%B2%8C%ED%85%94%20%EB%8C%80%EA%B5%AC%ED%82%A4%EC%8A%A4%EB%B0%A9%20%ED%83%80%EC%9E%84"

A "Quick 220" clone
Instructions from A "Quick 220" clone
Prepare the chassis.Drill a hole centered in each of the two "short" sides of the case sized for the CG-16 cable gland. Drill a hole sized for the L6-20 receptacle. The hole should be centered horizontally on the panel, but the top edge should be as...

TeensieWI woodwind USB MIDI controller
Instructions from TeensieWI woodwind USB MIDI controller
For the bottom sheet, make thumb rests/guides from 20 mm wide fabric tape. Center of top thumb rest is 70 – 75 mm from the top and the octave pads go directly above and below it. Center of RH thumb rest is 16 cm from the top. Try the placements out and...

Program firmware
Instructions from Crystal RGB
Once you confirmed the connection, proceed to write to your board the Arduino sketch in this project. You should be greeted with a rather bright LED cycling through colors.#include #ifdef __AVR__ #include // Required for 16 MHz Adafruit Trinket #endif...

Making the hardware
Instructions from FiberGrid
There are two versions of FiberGrid. One for R&D and testing. It features detachable fibers that can be disconnected from the grids. Both fiber ends are glued into small 3D printed connectors. The second is a "production version"...

RISC-V Instruction Set Architecture
Instructions from RISC-V Instruction Set Architecture
Install QEMU, a fast ISA SimulatorPrereqs: Linux or Mac OSXC compiler (gcc)Download the QEMU Source, either as a zip from Github, or using git:$ git clone https://github.com/ucb-bar/riscv-qemu.git Now, cd into the riscv-qemu directory and run the following....

RISC-V Instruction Set Architecture
Instructions from RISC-V Instruction Set Architecture
Build your own RISC-V Computer with a Zybo or ZedBoardHow it worksBoth the ZedBoard and the Zybo board contain Xilinx Zynq chips with an ARM processor tied to some programmable logic. We'll use the ARM core to bootstrap the RISC-V Rocket Core that we'll...

Install code.
Instructions from Wifi controlled stepper motor
Copy and paste the following code into the Arduino IDE. Update the AP name and password to match your needs. 90% of this code is not mine. For full details please see this great guide: https://randomnerdtutorials.com/esp32-esp8266-web-server-physical-button/...

Parts Details
Instructions from PROJECT MOOBA
Raspberry Pi B+: The Raspberry Pi 3 Model B+ is the final revision in the Raspberry Pi 3 range. Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz1GB LPDDR2 SDRAM2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLEGigabit Ethernet...

Wiring for UV Tube
Instructions from Ultraviolet Microwave (name subject to change)
My instructions errs on making the wires too long. It’s easier to fix mistake with longer wires than too short. You can follow the schematic for how to wire this up and skip the detailed instructions. Take one of the tube wires and form it so that it...

ESP8266 Driving an ebay TM1638 Button/7seg display
Instructions from ESP8266 Driving an ebay TM1638 Button/7seg display
To receive button presses via the tm1638 driver:Couple of interesting points here - Part way through I change an output to an input. I also map the odd button mapping across 4 bytes into a single byte. Teh basic sequence to read from the TM1638 isSet...

operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Instructions from operation: Learn The MIPS (PIC32MX1xx/2xx/370)
Wire up your PIC32's MINIMUM requirements as-shown:(a summary of the related Project Log)(NOTE: If this page wraps-weirdly, try *shrinking* your window-width, counterintuitively)( '#' = MUST BE CONNECTED ) ( '*' = 5V-tolerant ) 3V3 ^ | \ / 10K PIC32...

Up-Ride, the Bicycle to Elliptical Conversion Kit
Instructions from Up-Ride, the Bicycle to Elliptical Conversion Kit
Crank ExtensionProbably the trickiest element of this build.Crank face geometry is silly variable for aesthetic reasons. You may have to go for much thicker flat stock depending on your 3 piece crank (will not discuss 1 piece cranks here, if you want...

Yet Another (PiZero) Wi-Fi 'Hat'
Instructions from Yet Another (PiZero) Wi-Fi 'Hat'
Make sure your an SD Card breakout board which breaks out all 6 SDIO signals. Then wire the signals to the corresponding pins on your hat's gpio header, keeping the wire length as short as possible.SDIO SignalGPIO Pin #SD_CLK15SD_CMD16SD_DATA018SD_DATA122SD_DATA237SD_DATA3133v31...

FoocusStacker
Instructions from FoocusStacker
LCD displayThe LCD display is a generic 4 line 20 character module. It exposes a set of ~16 digital connections. Because the controller has a limited I/O count, the LCD module is connected through the I2C bus. The I2C bus to LCD2004 combination is quite...

Adjustable Angle Knife Grinding Jig
Instructions from Adjustable Angle Knife Grinding Jig
These are the parts I bought for the project:Everbilt 4.5" adjustable spring hinge - 1xMetal angle bracket (sturdy) - 1x3/8" - 16 x 2" SS Socket Cap Screw - 1pk3/8" - 16 x 7/16" T-Nuts - 2pk1/4" - 20 x 1" Flat Head machine screws with nuts - 4pkM10 Cap...

|<
<
3
4
5
6
7
>
>|