5943 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워ㅾ Йlife강남술집정보ħ쓰리아워레깅스룸강남쓰리아워７┢강남술집정보indignation 쓰리아워레깅스룸ケ쓰리아워ı㎃outside"

Put the HV supply in an enclosure
Instructions from DIY Scintillation Detector
Get a metal enclosure, drill holes for 2 connectors - 1 BNC and another one of your choice for 5V power.Drill another 2 holes on the other side - one for the Enable Switch and one for an optional multiturn 5K potentiometer (do not populate footprint...

Buy a Psion Organiser II
Instructions from Getting online with a 1987 Psion Organiser II
Start with the fun bit! Here's a short Organiser II buying guide I produced myself - consult the websites for more detailed/informed insights... There are four models of Organiser II - all should work with this project. I own two Organisers - a 1988-89...

Arduino or Wemos Code
Instructions from WiFi Signal Strength Scanner Monitor or Checker
In the arduino code set your WiFi credentials char wifissid[] = "ENTER YOUR WiFi SSID HERE"; char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE"; Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms...

Guerrilla MP3 Player / Audio Street Art
Instructions from Guerrilla MP3 Player / Audio Street Art
make or find a pretty box. over build it.a round box is cool, but a bit of a painmake your box hard to open unless you have neat toolsthis box is planned for being epoxy and screwed to a wall outside

The FireVolt Project
Instructions from The FireVolt Project
Using high shear-strength 1" long 1/4" dia hex bolts - mount the T-beams to the TEG water blocks, (Bolt head outside, Nut inside). Apply high temperature thread locker to every bolt prior to nut installation.

Mandalorian Infiltration Vambrace
Instructions from Mandalorian Infiltration Vambrace
Step 8: Never take it outside. This device contains intrusion software, destructive software, destructive hardware, and a legitimate weapon. These components are not illegal to own but certainly illegal to use on anyone or anything that is not you or...

Raspberry Pi Zero W desk clock
Instructions from Raspberry Pi Zero W desk clock
Remove the paper from both sides of the acrylic. Insert the remaining 6 3/8" nuts through the holes in the acrylic from the front (the AM and PM etching is on the outside / front of the panel). Loosely attach the remaining 6 nuts to the bolts, again,...

Basic build
Instructions from 3 Axis Gimbal
Assemble from the inside to outside (inside, middle, outer, outer #2). I used a washer on both sides of the joints for extra support. Use extra walls when printing the base so you can tap the 1/4-20 holes.

The Haunted Fish Tank
Instructions from The Haunted Fish Tank
First, I painted the inside of the box blackOn the outside I glued half wooden balls to make it look like rivets.With wooden spatula I made the surface rougher. I used wood glue to write the text on the front. Now let it dry for min. 24 hours. Then I...

J1772 Hydra
Instructions from J1772 Hydra
Prepare the button by connecting three wires to a 3 pin .1" female SIP header. The center pin should be red, the outside pins green and black. The button will have 5 terminals on it, marked +, -, C (or COM), NO and NC. Connect the red wire to the + terminal,...

Raspberry Pi Zero W desk clock
Instructions from Raspberry Pi Zero W desk clock
Place the back panel writing-side down on a flat surface. Thread the 4 1" bolts through the corners from the bottom (the outside of the finished case). On the bolt nearest the GPIO header cut-out, place the 3/16" standoff and on the other four, place...

Insert 4 shielded end glow fiber optic cables
Instructions from 3D printed Joystick
Insert fibers into four corners and align their edges with inner case edges. My fiber is a shielded 1 mm plastic core with a 2.5mm outside shield diameter. You might need to change the CAD files if you have a thinner or thicker fibers....

ESP8266Basic "A basic interpret for your esp"
Instructions from ESP8266Basic "A basic interpret for your esp"
How to flash the chip.Download the package from the download page Run "ESP_Basic_Flasher.exe"Select Your com port number and flash memory size for your chip.Hook your ESP8266 module up in flashing configuration as shown.Click the "Firmware Flash" button.Wait...

Programming
Instructions from PiTagErrUs
The Arduino Micro Pro doesn't like to play with [Ken Shirriff]'s infrared library. [Link]Follow the instructions for installing this library. Once the library is installed, it must be modified to work our hardware. This troubled me and I followed forums...

Running the board.
Instructions from GPS Dog Fence
Once you have code uploaded onto the electron and all of the components soldered onto the PCB you are ready to fence. In order to do this plug in both of the batteries to the PCB. Flip the on/off switch away from the TIP120 to the ON position. ...

1
2
3
4
5
>
>|