4954 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Test the X, Y, Z motors and end stops.
Instructions from DuePrint
If everything worked correctly you should now have control of the movement motors and end stops. Manually move the print head to the center of the printer. Next, the axes homing will be tested to ensure the motors are wired up correctly. Be prepared...

Step 3: Let's Connect Everything
Instructions from Smart Bluetooth Speaker with Spectrum Analyzer
The Bluetooth module is the F6188 module which is good and works very well. You might need to add a heatsink on top of the module as it heats up sometimes. The speakers are connected to PAM 8403 module and input to the module is given by the both...

Making Sure Everything is working
Instructions from UnifiedWater
It took me a long while to get things started. There was a lot of editing of libraries and Googling involved as documentation around connectivity was really limited to that one example above. But in the end everything worked. Below are some basic troubleshooting...

Cypress PSOC 4 + ESP8266 WS2812 RGB XMAS Lights
Instructions from Cypress PSOC 4 + ESP8266 WS2812 RGB XMAS Lights
Use P3_0 and P3_1 to communicate with the ESP8266 RX/TX via a 5v<>3.3v shifter., add UART component and config to 11500kbps, 1024 rx buffer, 128 tx buffer (or less) default everything else.Add a X to 3.3V VREG and power the ESP8266 and level shifter.Make...

The FireVolt Project
Instructions from The FireVolt Project
Step one is to get yourself an InStove 60L and get familiar with it. Boil some water, try different fuels, play around. Everything related to the build is downstream from this. At worst, if this is as far as you get, you'll be able to cook huge amounts...

SAB3T - PID Loop Educational Tool
Instructions from SAB3T - PID Loop Educational Tool
Universal Joint 4 WayYou Need: - everything from the previous step - universal joint 4 way - 2 screwsThe holes in the universal joint mounting plate are slightly larger than the holes in the 4 way. This will allow the screw to spin freely in the mounting...

Bike improvement: fitting a rack
Instructions from Bike improvement: fitting a rack
Go to the hardware store. For this project the following supplies were needed:2 x 50mm L-shaped mounting brackets1 x M6 screw, 40mm long1 x M6 washer1 x M6 locknut (it resists better to the vibrations than regular threaded nuts)2 x M5 locknuts (the rear...

ESP-12 and ESP-14 adapter to DIL
Instructions from ESP-12 and ESP-14 adapter to DIL
Insert each of the 11-pin header strips into the base plate, with the short ends being exposed against the supporting block in the middle of the adapter. I heated each pin just enough to melt some solder to each of the short ends, ready for the wire...

DIY Jukebox With Raspberry Pi
Instructions from DIY Jukebox With Raspberry Pi
Step 1: REQUIRED COMPONENTSRaspberry Pi 2 or 3 // ~$10~$3516 GB SD card // ~$8Big breadboard // ~$4GPIO buttons + jumper and hook-up wires // <$2speakers ~$0usb stick ~$0philips hue bulb ~$10-$20you can get everything for around $50.< body></$2speakers>...

Final Test
Instructions from SOLAR POWERED WIFI WEATHER STATION
Place the device on sunlight, the red led on TP 4056 charger module will lit up. 1. Blynk App Monitoring: Open the blynk project.If everything is Ok,you will notice the gauge will live and the graph stat to plot the temperature data. 2. ThingSpeak Monitoring...

Wiring Arduino to transistor and relay
Instructions from MacBook Speech Recognition Starts A Jeep
Here is a diagram for the KRPA-11DG-12 relay which I found at https://www.digikey.co.il/product-detail/en/te-connectivity-potter-brumfield-relays/KRPA-11DG-12/PB169-ND/45030: If you are not familiar with electromagnetic relays, they are basically a switch...

Drilling Part I
Instructions from Ender 3 PCB Drilling
Place the PCB to be drilled on top of a cardboard sheet (it doesn't need to be thick, mine is 1mm), which goes on top of the Ender 3 printing table. Hold everything with clamps on the corners. Alternatively, you might use double-sided stick tape.Manually...

Prepering powerbank
Instructions from PocketWhale
In parts i have puted link to powerbank that i am using. To make conectror for it you will need: 1 USB C cable, 1 micro USB cable and 2 USB A cables. Now take printed part (powerbank holder) put it on top of powerbank and to holes put all cables. USC...

END
Instructions from Crius Vertical Infinity Control-Arduino USB MIDI
I hope you enjoyed the proccess and made one for your self! You can find everything you need for this project INCLUDING INSTRUCTIONS IN ENGLISH to my website : www.criusdigitalstudio.com You can find my projects and support me at the following social...

Norman, Coordinate
Instructions from Norman, Coordinate
Build the control switch Step 1: Thread a short piece of wire through the ring and the switch. Step 2: Twist the wire until the switch is solid against the ring. Step 3: Test it for fit and comfort. Step 4: Connect/solder the switch to D11-D12 on the...

|<
<
1
2
3
4
5
>
>|