Close

42 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ 《〈 문의 OIO↗5793↗7458 》〉 ㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ"

  • Raspberry Pi 3 Gameboy
  • Instructions     from Raspberry Pi 3 Gameboy
  • 12. Gluing in the analog sticks and programming the leonardo pro microI glued in the analog sticks and soldered the corresponding wires to them. I then wrote a program to turn the leonardo into a USB joystick with 14 buttons and two analog inputs and...

  • WiFi World Clock
  • Instructions     from WiFi World Clock
  • X-8266 x1X-OLED x118650 battery shield V2 x1Simple 3D printed case X1You can have a look at the pin map.SDA is connected to D1.SCL is connected to D2.This two pins work as the IIC pins.The other pins can be connected to other sensors.The X-8266 can really...

  • Finish the mechanical build.
  • Instructions     from InspectorBot
  • Insert five additional wires through the grommet on the top cover of the box. I cut over-sized wires so I can cut them to size later. The colors do not matter, but I like to have one red wire for the positive connection. On the top cover of the Raspberry...

  • Creating the L298n Circuit
  • Instructions     from Volturnus ROV
  • The primary purpose of the circuit on our ROV is to take input from a program and use this input to control the motors.  Obtain 2 L298n motor controllers.Connect the 12 volts and ground to the two terminals. Connect the 5 volts terminal to...

  • DIY: Become a Machine!
  • Instructions     from How to become a machine.
  • Let's make the machine restrict our body and create our human/machine symbiosis.  Here is a list of materials needed:  x3 Arduino MEGA 2560 controllersx2 Motor Shieldx1 DHT 22 Temperature/humidity/gas sensorx3 12 batteriesAcrylic pieces to...

  • Tools and Materials
  • Instructions     from Joy Robot (Robô da Alegria) 2017 edition
  • The following tools and materials were used for this project: Tools: 3D printer - The whole body of the robot is 3D printed. Several hours of 3d printing were needed for building the whole structure;PLA filament - White and black PLA filaments...

  • Slide the Y axe driver parts.
  • Instructions     from Veletiskárna - 3D Printer home made
  • Slide the Y belt holder part and his nut on the front frame.x1 Y belt holder printed partx1 screw M3x20mmx1 nut M3x2mmx1 screw M6x12mmx1 coller nut M6 Set one motor on the Y beld holder printed part and slide the assemblage on the rear frame.x1...

  • Slide the Y printed bearings.
  • Instructions     from Veletiskárna - 3D Printer home made
  • Use sandpaper and lubricating grease.x2 Y printed bearingsx1 lubricating grease pot The bearings have to slice very easily. Then slice x3 M6 coller nuts at the oposite chanel from the bearings and x2 M6 coller nuts on the top. Like the picture....

  • Built the X axe driver parts.
  • Instructions     from Veletiskárna - 3D Printer home made
  • You also have to use sandpaper and greace for the parts going in the frame. Motor sidex1 Motor holder for X axe printed partx1 Motorx3 screws M3x8mmx1 Motor to belt (pulley) Between the printed partsx1 Nozzle holder printed partx1 Beltx2 Rods  On...

  • Build the bed and assemble it.
  • Instructions     from Veletiskárna - 3D Printer home made
  • x1 big metal platex2 small metal platex2 big angle plate printed partsx2 small angle plate printed partsx1 Belt to bed printed partx2 small bed to bearing parts x2 big bed to bearing partsx20 screws M5x12mmx20 stop nuts M5x8 washer M5x4 screws M3x30mmx8...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday