Close

13578 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》선릉레깅스룸㉹ベgrace레깅스룸Ｓ선릉레깅스룸선릉레깅스е я레깅스룸비용superstition 강남레깅스룸′강남레깅스§８fetch"

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Now is a good time to test your LCD and make sure it still works. Load the batteries back into the back half of the case. Press the motherboard against the back half of the case so the battery connectors make contact. Use a screwdriver or some other...

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • On the back of the LCD there is a reflector and a polarizer. This diagram shows the different layers.The reflector is a thin foil sheet on back of the polarizer. It needs to be removed so the backlight can shine through. The polarizer is a thicker plastic...

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Take the new polarizer film and slide it behind the LCD. If you turn the polarizer one way, the screen will be transparrent. If you turn it the other way, the screen will be opaque. Behold the magic of polarized light!Now you have the option of inverting...

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Find a good place to mount the push button that will control the backlight. I chose to put mine on the left side of the calculator, as you can see in the pictures. This was a very tight fit though. Some other suggestions would be on the top or under...

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Carefully bend the EL panel leads so they fold around the back of the PCB. The panel can bend pretty far, just don't crease it.Now install the board back in the front half of the case and screw it down. The EL panel leads will stick up through gap between...

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Use hot glue to mount the inverter and push button in the back half of the case. Fortunately theres lots of space inside the TI. Use lots of glue so the button stays in place when you push it.

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Finally you can put the two halves back together. Plug in the EL panel and arrange all the wires so they don't get pinched. Snap the two halves of the case together.Before you screw everything together, put the batteries in and make sure it all works....

  • TI-84+ SE Backlight
  • Instructions     from TI-84+ SE Backlight
  • Now its time to take apart the inverter. Clip off the spring and solder some wires onto the battery contacts. The inverter will be powered by two of the calculator's AAs.The inverter has two buttons, but they both do the same thing. Desolder the button...

  • DIY SlingBox $30
  • Instructions     from DIY SlingBox $30
  • VLC:Live transcoding is resource intensive, making it nice to be able to turn it on and off. Also switching the VLC configurations allows for many variations of size and quality, useful in tailor the stream to different devices and scenarios. Below are...

  • HP Touchpad Charging Wall Mount
  • Instructions     from HP Touchpad Charging Wall Mount
  • I took the end of an extension cord and wired it to power from the switchbox below to accept the plug-in charger for the Touchstone. I had a switchbox on the opposite side of this wall that could house the charger and keep it accessible for safety and...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday