6194 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Assemble
Instructions from Wireless BLE Kinesis Advantage (Custom Controller)
I tried to label all the parts on the PCB and everything lines up so it should be pretty easy. If you're having trouble soldering the pins on the flex connectors, get a better iron! I upgraded to a fx-888 and my soldering time for the board went...

My device
Instructions from Wi-Fi Jammer from an ESP8266 | WiFi Deauther
I added a battery and a switch and hot glued everything.

Place everything in the case
Instructions from Robotics Ground Control Station
Before putting the panels in make sure to screw the threaded rods into the lid, so that they stick ~3 cm out. Place the bottom panel first, just slide it in. Then place the front panel and secure it with the 4 3d printed nuts. Check that you can close...

PixiFlood
Instructions from PixiFlood
Solder: WS2811S (IC2) to PCB. Same warnings as the PT4115B.That is the last of the SMT/SMD components, everything from this point forward is Plated Through Hole (PTH).Stage 1 Assembly is complete. At this point you are ready to conduct the first series...

SAB3T - PID Loop Educational Tool
Instructions from SAB3T - PID Loop Educational Tool
Universal Joint 4 WayYou Need: - everything from the previous step - universal joint 4 way - 2 screwsThe holes in the universal joint mounting plate are slightly larger than the holes in the 4 way. This will allow the screw to spin freely in the mounting...

U8 SmartHack
Instructions from U8 SmartHack
Here we go, Start Address is fine, remove the 8 and add a 4. So make it look like 0x00400000. (ive read somewhere 0x01000000 would be the whole device, but that was for the official U8, we have a clone) (most)All "Russian" and XDA tutorials use this...

Electromagnetic Teaching Aid
Instructions from Electromagnetic Teaching Aid
At this point take the other half of your electrical tape and wrap it around to keep everything covered and in place. I also like to cut a little away around the LEDs so they can be seen well from above. I have been using paper hole reinforcement stickers...

Bike improvement: fitting a rack
Instructions from Bike improvement: fitting a rack
Go to the hardware store. For this project the following supplies were needed:2 x 50mm L-shaped mounting brackets1 x M6 screw, 40mm long1 x M6 washer1 x M6 locknut (it resists better to the vibrations than regular threaded nuts)2 x M5 locknuts (the rear...

DIY Jukebox With Raspberry Pi
Instructions from DIY Jukebox With Raspberry Pi
Step 1: REQUIRED COMPONENTSRaspberry Pi 2 or 3 // ~$10~$3516 GB SD card // ~$8Big breadboard // ~$4GPIO buttons + jumper and hook-up wires // <$2speakers ~$0usb stick ~$0philips hue bulb ~$10-$20you can get everything for around $50.< body></$2speakers>...

Final Test
Instructions from SOLAR POWERED WIFI WEATHER STATION
Place the device on sunlight, the red led on TP 4056 charger module will lit up. 1. Blynk App Monitoring: Open the blynk project.If everything is Ok,you will notice the gauge will live and the graph stat to plot the temperature data. 2. ThingSpeak Monitoring...

Step 3: Connect everything
Instructions from Convert your old phone into a remote switch
Connect these wires to one of the GPIOs of Arduino. Here I'm using pin number A0. And negative pin to ground. LCD connections are as usual. Relay module signal pin to pin number 4 and VCC, GND to Arduino's VCC and GND. You can use jumper wires for...

Step - 4 : Insert everything in glove
Instructions from Gadget for Visually Impaired People (GVIP)
Carefully insert in glove. Different glove need different technique to insert. If you use a bicycle glove you can insert arduino and all other component user its plastic protection. See this picture for an idea. Make sure sensor is in correct position....

Wiring Arduino to transistor and relay
Instructions from MacBook Speech Recognition Starts A Jeep
Here is a diagram for the KRPA-11DG-12 relay which I found at https://www.digikey.co.il/product-detail/en/te-connectivity-potter-brumfield-relays/KRPA-11DG-12/PB169-ND/45030: If you are not familiar with electromagnetic relays, they are basically a switch...

Assembling the hardware
Instructions from Skin Temperature Scanner
Solder the pins to the breakout board of the thermal sensor. Connect the 5 pins of the thermal sensor to the first 5 pins of the GPIO on the Raspberry Pi: 5V -> pin 1SDA -> pin 3SCL -> pin 5INT -> pin 7GND -> pin 9 Screw the display to the Raspberry...

Prepering powerbank
Instructions from PocketWhale
In parts i have puted link to powerbank that i am using. To make conectror for it you will need: 1 USB C cable, 1 micro USB cable and 2 USB A cables. Now take printed part (powerbank holder) put it on top of powerbank and to holes put all cables. USC...

|<
<
1
2
3
4
5
>
>|