3147 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

Arcade Control Panel
Instructions from Arcade Control Panel
Step 5 - If you are following my build exactly, you now have a nice looking piece of plywood with a lot of holes in it. Next you'll need to use a forstner bit to make a shallow recess for the top of the T-Nuts to sit flush with the top surface...

Arcade Control Panel
Instructions from Arcade Control Panel
Step 8 - Mount you controls to your panel. While it is not technically a necessity, I HIGHLY recommend you order the wrench for the button nuts. They would not be at all fun to install without it.

TI Launchpad Arcade Control to USB Interface
Instructions from TI Launchpad Arcade Control to USB Interface
Launchpad-Mame-Control TI Tiva C Launchpad firmware for Mame USB arcade controls adapterThis project is intended to design firmware for the TI Tiva C Launchpad development board to enable it to be used as a USB gamepad/mouse adapter for arcade and other...

Peril-Sensitive Sunglasses
Instructions from Peril-Sensitive Sunglasses
Analog 5 is the ambient light sensor. It outputs an analog voltage that is proportional to the amount of light it is exposed to.I mounted it inside the glasses frame.

Wireless Flux Capacitor
Instructions from Wireless Flux Capacitor
1. The first thing I did after coming up with the idea is to find a way to control 3 sets of 8 leds on each with a minimum amount of wires. I found an article that talked about shift registers and went ahead and ordered a few to try them out. following...

Wireless Flux Capacitor
Instructions from Wireless Flux Capacitor
5. next I setup a node server to get the likes from this project and update the delay of the flux capacitor.

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Create (etch and solder) 5 PCB from big-module-shift and big-module-test - those are the display PCBs and drivers for 14-segment displays.

Mk 16 Capital Ship MDM
Instructions from Mk 16 Capital Ship MDM
Build Payload MPDB:1) 3D printed parts needed 1x MPDB 1a1x MPDB 1b1x MPDB 21) Cut Material: Cut 1" tubing to 212mmCut 3/8" tubing to 130mmCut 3/8" tubing to 30mm2) Construct Take 30 mm section of 3/8" tubing and place it into the center hole in...

Battery Tutorial for SG circuit
Instructions from Battery Tutorial for SG circuit
Greetings fellow Enthusiasts Let me introduce myself. I'm Bones MacGyver. I like to make sparks.I'm going to do my best to help out the community with their battery woes.By no means am I a battery expert. But I have used and abused MANY Ni-Cd cells (and...

The Dune Pain Box
Instructions from The Dune Pain Box
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...

Animatronic AVP Predator cannon
Instructions from Animatronic AVP Predator cannon
Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

Mini Potato Cannon
Instructions from Mini Potato Cannon
5.) Bend both ends of the paperclip down the sides of the bottle and tape them in place.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
2.) Wrap the paperclip very tightly around a small, 1/8 inch diameter rod or screwdriver.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
5.) Follow your favorite chainmaille pattern, using 2 pairs of needle-nosed pliers.

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Power to Servo motor So, we've written the code. Now start all wiring stuff:We have two options:Give 5V to servo motor from Arduino.Here, you can connect the servo motor ( attach a small fan to the motor ) to Arduino Uno. Servo motor has 3 wires: Connect...

|<
<
1
2
3
4
5
>
>|