3734 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워㏃㏐addition쓰리아워Ⅶ강남술집정보강남술집정보Ｏ Ч강남술집정보exhibit 강남쓰리아워к강남술집정보㎼Ŋmethod"

TI Launchpad Arcade Control to USB Interface
Instructions from TI Launchpad Arcade Control to USB Interface
Launchpad-Mame-Control TI Tiva C Launchpad firmware for Mame USB arcade controls adapterThis project is intended to design firmware for the TI Tiva C Launchpad development board to enable it to be used as a USB gamepad/mouse adapter for arcade and other...

Peril-Sensitive Sunglasses
Instructions from Peril-Sensitive Sunglasses
Analog 5 is the ambient light sensor. It outputs an analog voltage that is proportional to the amount of light it is exposed to.I mounted it inside the glasses frame.

Wireless Flux Capacitor
Instructions from Wireless Flux Capacitor
1. The first thing I did after coming up with the idea is to find a way to control 3 sets of 8 leds on each with a minimum amount of wires. I found an article that talked about shift registers and went ahead and ordered a few to try them out. following...

Wireless Flux Capacitor
Instructions from Wireless Flux Capacitor
5. next I setup a node server to get the likes from this project and update the delay of the flux capacitor.

Back To The Future Time Circuit Clock
Instructions from Back To The Future Time Circuit Clock
Create (etch and solder) 5 PCB from big-module-shift and big-module-test - those are the display PCBs and drivers for 14-segment displays.

Mk 16 Capital Ship MDM
Instructions from Mk 16 Capital Ship MDM
Build Payload MPDB:1) 3D printed parts needed 1x MPDB 1a1x MPDB 1b1x MPDB 21) Cut Material: Cut 1" tubing to 212mmCut 3/8" tubing to 130mmCut 3/8" tubing to 30mm2) Construct Take 30 mm section of 3/8" tubing and place it into the center hole in...

Battery Tutorial for SG circuit
Instructions from Battery Tutorial for SG circuit
Greetings fellow Enthusiasts Let me introduce myself. I'm Bones MacGyver. I like to make sparks.I'm going to do my best to help out the community with their battery woes.By no means am I a battery expert. But I have used and abused MANY Ni-Cd cells (and...

Desktop Tamagotchi
Instructions from Desktop Tamagotchi
Check Instructables.com for a full step by step instructions.http://www.instructables.com/id/Make-a-Desktop-Tamagotchi/

Smoke 'Detector'
Instructions from Smoke 'Detector'
Step-by-step build instructions are on Instructables.com http://www.instructables.com/id/Smoke-Detector/

The Dune Pain Box
Instructions from The Dune Pain Box
Winding the inductors is easier than you might think! I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply. Each inductor has ~30 turns on it for an inductance of about 90uH. If you don't have...

Animatronic AVP Predator cannon
Instructions from Animatronic AVP Predator cannon
Cannon code- #include "Servo.h" // include the servo library Servo armServo; // servo to raise the arm Servo cannonServo; // servo to recoil cannon // these constants won't change: const int triggerSensor = 1; // the sensor is connected to analog pin...

Mini Potato Cannon
Instructions from Mini Potato Cannon
5.) Bend both ends of the paperclip down the sides of the bottle and tape them in place.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
2.) Wrap the paperclip very tightly around a small, 1/8 inch diameter rod or screwdriver.

Paperclip Chainmaille
Instructions from Paperclip Chainmaille
5.) Follow your favorite chainmaille pattern, using 2 pairs of needle-nosed pliers.

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Start drawing on Processing First lets create a code on Processing, which lets you draw freehand on the computer.Download Processing from https://www.processing.org/download/ .Here is the processing code:int prevX=mouseX, prevY=mouseY; //to record previous...

|<
<
1
2
3
4
5
>
>|