58 Results for "Reverse Engineering Blood Glucose Monitors"

PORTs - How to use them?
Instructions from Getting Started with TivaWare Launchpad - Basics ⚓
Ports are the peripheral pins on an embedded system, or SoC to communicate with the external environment. Whenever a port receives a HIGH or LOW signal, it communicates throughout the system. A PORT is usually bit-packed, i.e. each port is represented...

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
18. Preparing the LED connect cables for testingNow that all the LEDs are wired up, there are two simultaneous tests that need to be done:1.Test the LEDs to make sure they’re all wired up and working properly2.Test the MOSFET/CAT4101 driver board combination...

Analysing the code
Instructions from ESP8266 SDK Tutorial, Part 3
As we've established in prior tutorials, every program written with the ESP SDK needs to have a function called user_init(). This function is called by the SDK once it has finished the boot process. Much of the code in our example revolves around getting...

Mechanicals
Instructions from Basic Farm Robot 2021
In previous projects we spent a lot of time designing and building the mechanical systems and we really wanted to short cut all the hard work by using a ready made system that could be bought reasonably cheaply 'off the shelf'. We looked at mobility...

analog2pi
Instructions from analog2pi
Build it like this. Orange and purple are inputs, black is ground.CALIBRATIONNOTE: These instructions are for a character device kernel module. I will re-write them when I finish a proper sound device kernel module. They're also horribly confusing -...

ps2pi
Instructions from ps2pi
BUILDING ITYou'll need a mini DIN 6-pin socket to connect to the keyboard. It can be scrounged from an old keyboard adapter, or you can eliminate it altogether by cutting the connector off the keyboard cable and wiring it directly to the interface. Refer...

pi2meter
Instructions from pi2meter
FINDING THE RESISTOR VALUESolder a 10K resistor to the Zero's header connector hole at pin 12, and connect the other end to the meter plus terminal. The meter minus terminal is connected to pin 14. To test it type the following: sudo gpio -g mode 18...

▇▇▇▇ Real World Background ▇▇▇▇
Instructions from FPGA Bootcamp #0
Digital design with combinatorial gates like AND, OR, and NOT gates is relatively straightforward. In particular, when you use these gates to form combinatorial logic, the outputs only depend on the inputs. The previous state of the outputs isn’t important...

Switch on your soldering iron, it's time to...
Instructions from miniDenko
All the parts (except screws, some SMD parts, wires)R3: 33kR1, R2, R4, R5: 10k U1: xc6206p332mrC1: 1uFU2: ESP-12F Push down the plastic part on the 2.54mm 1 x 8 pin header to not stick out from the back side of the PCB. J5: GY-521 Pay extra attention...

Parts Details
Instructions from PROJECT MOOBA
Raspberry Pi B+: The Raspberry Pi 3 Model B+ is the final revision in the Raspberry Pi 3 range. Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz1GB LPDDR2 SDRAM2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLEGigabit Ethernet...

LoRaWAN Gateway and It's Working
Instructions from LoRaWAN Gateways tutorial | LoRa | What is LoraWAN
In the previous steps, we got to know that we get a LoRaWAN by connecting our LoRa based network to the Internet. But for connecting the LoRa network to the Internet, we need a LoRaWAN Gateway. One thing that needs to be mentioned here is that connecting...

Fairly straightforward
Instructions from Neo Geo controller for Nintendo NES and Famicom
Requirement: multi-meter (in OHMs setting), soldering iron, wire cutter, and wire strippers, and have some soldering experience. I used all larger through hole components for easier soldering. If you do not have the equipment or the soldering experience,...

Code Explanation
Instructions from BrailleBot
setup(): This function is called once when the Arduino starts.It sets up the pin modes for the "Next" and "Previous" buttons, initializes serial communication, and attaches interrupt service routines to these buttons.It initializes the DFPlayer module,...

Battery Tutorial for SG circuit
Instructions from Battery Tutorial for SG circuit
Greetings fellow Enthusiasts Let me introduce myself. I'm Bones MacGyver. I like to make sparks.I'm going to do my best to help out the community with their battery woes.By no means am I a battery expert. But I have used and abused MANY Ni-Cd cells (and...

Finish the mechanical build.
Instructions from InspectorBot
Insert five additional wires through the grommet on the top cover of the box. I cut over-sized wires so I can cut them to size later. The colors do not matter, but I like to have one red wire for the positive connection. On the top cover of the Raspberry...

|<
<
1
2
3
4
>
>|