394 Results for "%E3%80%8A%EC%B5%9C%EC%A0%80%EA%B0%80 O1O%CE%9E5793%CE%9E7458%E3%80%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%E3%86%8B %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%85%94%EC%B8%A0%EB%A3%B8applause%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%EC%8B%9C%EC%8A%A4%ED%85%9C%EC%8B%A0%EC%82%AC%EC%95%84%EC%9D%B4%EB%A6%B0%EC%A3%BC%EB%8C%80caught %EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0%E3%8F%87%E3%85%97%EA%B0%95%EB%82%A8%EC%95%84%EC%9D%B4%EB%A6%B0queer"

Arduino Code
Instructions from OBS_IRL_STREAM_DECK
It's in the GITHUB! The code comes down the these smaller steps: MQTT handling and Button handling. Let's do button handling first. I made a simple button object with the pin number, button press boolean, and button count. struct Button { const uint8_t...

▇▇▇▇ D Flip Flops ▇▇▇▇
Instructions from FPGA Bootcamp #0
The SR latch modified with the inverter is often called a D latch because the single input is data for the latch to store. To make it a D flip flop, though, you need to arrange to capture the data at a clock edge, not just any time the latch is enabled....

Code for single Esp32 Board
Instructions from Bluetooth Tracker
This is the code for everything on a single Esp32 Board. Since I didn't have the correct board, I needed to use two of them, and they communicate through the serial port.The Bluetooth packets address and raw data get printed to the Arduino Serial...

HariFun#132 Sixteen Channel WiFi Remote
Instructions from HariFun#132 Sixteen Channel WiFi Remote
=== WebServer Sketch ===// PCF8574 WebServer, listens for /inline?state= // Hari Wiguna, 2016 #include #include #include #include // Declare and set these two variables here or in an include file //const byte credentialCount = 2; //IMPORTANT! Change...

HariFun#132 Sixteen Channel WiFi Remote
Instructions from HariFun#132 Sixteen Channel WiFi Remote
=== WebClient Sketch ===// PCF8574 WebClient, watches buttons and sends /inline?state=x to WebServer // Hari Wiguna, 2016 #include // Declare and set these two variables here or in an include file //const byte credentialCount = 2; //IMPORTANT! Change...

Assembly Code
Instructions from 8051 Alarm Clock
ROA EQU 7FH ;es Reloj o es Alarma USR EQU 50H ;Unidades de Segundos del Reloj DSR EQU 51H ;Decenas de Segundos del Reloj UMR EQU 52H ;Unidades de Minutos del Reloj DMR EQU 53H ;Decenas de Minutos del Reloj UHR EQU 54H ;Unidades de Horas del...

Wiring the Circuit
Instructions from The Wireless Tin Can Telephone
Once everything is securely glued in, it’s time for wiring! Use the provided schematic to connect all the jumpers to their appropriate pins. I’ll also provide the pin-outs below: (Note, this is for the Gravity Expansion HAT) Antenna Board: MI -> MISOMO...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
I attached a 2 axis gyroscope and 3 axis accelerometer onto this project so that I could add some interesting control to the device. The 5 degrees of freedom board from Sparkfun outputs data from its gyroscope and accelerometer as analog voltages. I...

Circuit Connection:
Instructions from DIY Arduino Tic Toc Toe Game
Connect the push buttons keypad to Arduino Uno as shown in circuit diagram.(R1~A0,R2~A1,R3~A2,R4~A3,C1~A4,C2~A5,C3~Pin 2,C4~Pin 3).Also take a extra push button(Reset Button) and connect to Arduino.(Reset,GND).Connect all the pixel LEDs.(-Ve/GND~GND,+Ve/5V~5V,Data...

DIY Data Logger
Instructions from DIY Data Logger
Here's the code for the Spark Core. The programming for this is very similar to an Arduino. Once you go to the Spark website and get your Core setup you just click on the BUILD tab, create a new App and paste in the code and it'll upload the code over...

Prep Your Board!
Instructions from Sotto: A Silent One-Handed Modular Keyset
Cut your protoboard to roughly fit the size of the Feather. Use your wires to take the inconveniently placed pins and turn them into tidy little rows of four. The rows should be: A0 3v Gnd 11 A1 3v ...

Trinket LED Thermometer
Instructions from Trinket LED Thermometer
Here's a functional program to initialize the hardware, read temps, and display temps as colors. Enhancements such as multiple sensors/LEDs per Trinket are possible but left as an exercise for the reader./* trinket_thermo ---------------------------------------------------------------------------------...

Redtree Hydra: A modular platform for robotics
Instructions from Redtree Hydra: A modular platform for robotics
Setting Up the EnvironmentRedtree Hydra currently requires a Ubuntu or Debian based development environment. For the remaining instructions, open the terminal application in Ubuntu. In Ubuntu It can be found by clicking the Ubuntu search icon on the...

Setting Up the Drone Transmitter
Instructions from DIY Radio Controller for Drone | nRF24L01
In this step, we will complete the Transmitter setup. We will do the circuit part first and after that, we will upload the code to the Arduino UNO to wrap up the setup. The materials required for this step are the NRF24L01 Transceiver module, Arduino...

Run a Program
Instructions from IoT Digital Thermometer using LM35 and NodeMCU
#include const char* ssid = "*********"; // Your ssid const char* password = "***********"; // Your Password float temp_celsius = 0; float temp_fahrenheit = 0; WiFiServer server(80); void setup() { Serial.begin(115200); pinMode(A0, INPUT); Serial.println();...

|<
<
4
5
6
7
8
>
>|