14454 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 강남쓰리아워㎰ 쓰리아워fearful쓰리아워레깅스룸쓰리아워강남술집정보constructed 쓰리아워가격ペゴ쓰리아워wealthy"

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
Just add a single layer of tape, butting edges together to keep it flat and smooth.

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
I took the end of an extension cord and wired it to power from the switchbox below to accept the plug-in charger for the Touchstone. I had a switchbox on the opposite side of this wall that could house the charger and keep it accessible for safety and...

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
Add a wood backer strip with a couple of dry wall screws, a 1x2 or a paint stirring stick will work.

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
Test fit the depth once placed in the wall. Depending on your wallboard thickness it should sit just below the surface of the wall so you can use drywall compound (mud) to cover it.

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
Now add a backer piece of wood above the Dock so you can screw the magnets to the wall securely. Notice I started mudding it in before I realized I missed this step.

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
Screw two neodymium magnets to the backer wood, making sure to keep them just below the surface of the wall.

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
Spread it smooth so you won't have to do a lot of sanding later, but you may have to sand and do another thin finish coat.

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
Test it with the HP Touchpad to see if it charges through the thickness of mud. IT DOES!

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
Now to add some thin metal strips to the back of the HP Touchpad. I just used some black painted metal plates I had and some 3M Double sided tape. Bend the metal to follow the curve of the Touchpad's back.

Wearable computer
Instructions from Wearable computer
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

Wearable computer
Instructions from Wearable computer
The board with the USB-like connector on it will be connected to the colored wires via surface-mount solder on top of vias. This is a really bad thing for the kind of torque you are likely to put on this connector board. So, desolder these wires using...

Wearable computer
Instructions from Wearable computer
Unscrew one of the threaded caps on the goggles and remove the clear plastic pane. (Your pair may have a silvered or coloured glass pane on top; if so, remove this as well but do not drill into it -- discard it or keep it as backup for the other side.)In...

Wearable computer
Instructions from Wearable computer
Take a lens housing. Remove the lens and flip it over, then clip it to the other side of the housing. Put a thin layer of superglue along the edge of the lens housing (on the opposite side from the lens itself) and place it firmly atop the pane, on the...

Wearable computer
Instructions from Wearable computer
On the board containing the USB-like connector, on the edge opposite the connector whose wires you have resoldered, fold a piece of velcro. Connect the connector and then position a piece of velcro of the opposite type on top of your mask based on where...

Wearable computer
Instructions from Wearable computer
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

|<
<
1
2
3
4
5
>
>|