14454 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 강남쓰리아워㎰ 쓰리아워fearful쓰리아워레깅스룸쓰리아워강남술집정보constructed 쓰리아워가격ペゴ쓰리아워wealthy"

Trimming the screen
Instructions from Projector Screen
Run the motor in the 'screen up' direction. Take a brand new, sharp razor knife and hold it against un-even ends of the rolled up fabric. Make sure the direction of travel of the material is going away from you, so the knife does't bind in the cut and...

The control circuit
Instructions from Projector Screen
The relay coil is driven by 'remote power' output on the projector. There are no other connections made to the coil. As such, this also performs the needed isolation so if you screw up anything else, you at least don't fry your projector. The projector...

Final assembly
Instructions from Projector Screen
Put it up on the wall and level it. One day in the sun will remove any wrinkles, or careful application of a hair dryer will do the same. Don't overheat it as the plastic inside can expand and ruin it.Tweak the stop positions. Applying...

Web based solar panel monitoring/managment
Instructions from Web based solar panel monitoring/managment
The project is just a typical bread board project. use what ever techniques your comfortable with. I use a mix of soldering for the voltage and current collectors and use wire wrap to tie those collectors back to the Arduino. One mistake I made that...

LED Hoodie
Instructions from LED Hoodie
Sew the gemma onto the hoodie in a location that is relatively close to where you are putting the leds.I put it on the inside of the left half of the hoodie.Make sure you read adafruit's guide on sewing with conductive thread, especially the part about...

One Bad A$$ Power Inverter
Instructions from One Bad A$$ Power Inverter
The schematics I based my inverter on I found here -http://www.eserviceinfo.com/downloadsm/61386/DROW%...I did not deviate from the design except with my choice of Mosfets , Diodes and Transformers.

Smile Station
Instructions from Smile Station
On this next link is where I got the info for sending the photos taken with its own email account .http://mitchtech.net/connect-raspberry-pi-to-gmail...I tested it by copying the script to send attachments in to the python editor on the rpi by first...

Smile Station
Instructions from Smile Station
Well in this step I will focus on the code and getting it to work with Facebook and Flickr ....---------------------------------------------------------------------------------------------------------#!/usr/bin/env python# this file is run using this...

Smile Station
Instructions from Smile Station
Ok I pored the cement in the tube with a blue foam board on the bottom glued to the sides. That seemed to work out well accept I stuck a blue foam board cutout with a hole cut out in it to keep the 2" pvc pipe in place. Bad Idea it moved the PVC pipe...

Smile Station
Instructions from Smile Station
From the last step you should have seen how to and where every thing is going. So lets get started with the power... I used a PC power supply I had. ( 500 Watt ) I cut out the + 12 v and rigged the power supply to come on when power is applied. ...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
Build the base station using the following simple steps:Disassemble the outlet controller remote and throw away the plastic casingSolder wires between the +5v line on the Arduino and the positive battery terminal on the remote.Do the same with the ground...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
For the end of the base steps: Plug an outlet switch in between each outlet you want to control and whatever you want it to control. Not that you need a picture, but:Congrats! You now have a passable web-based home automation system. Stay tuned...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
For the outlet power detectors:Cut the connectors off of your two wall warts and solder the grounds together (and to the ground on their Arduino)Solder the +5v wire of one wall wart to the +5v plug on the Spark core, and the other to digital input 3...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
For the Androids involved:This one requires a bit more customization (unless you want a floorplan of my apartment in your system for some reason). You will need to download Unity and adjust the app to your needs. I am not planning on providing complete...

Sci-fi grade Home Automation
Instructions from Sci-fi grade Home Automation
To build the light switches (I'm not using these, but they might work better for those of you who don't rent):Using the pictues below as guides, solder the relevant wires to the Arduino...I kid.There are a few important parts here: There's the Arduino,...

|<
<
4
5
6
7
8
>
>|