319 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Home Automation - Garage Door Opener
Instructions from Home Automation - Garage Door Opener
openhab.local - gdoPi Interface SupportDownload the provided project files for openhab.local and install in their appropriate directories. Make sure to reset ownership to 'openhab' user./etc/openhab/configurations/openhab.cfg/etc/openhab/configurations/items/default.items/etc/openhab/configurations/sitemaps/default.sitemapsudo...

3DOF Hexapod (Hexapi)
Instructions from 3DOF Hexapod (Hexapi)
To hook up the ssc-32U to the PI, you will need a SparkFun Voltage Level Translator or something similar. The ssc has a logic level of 5 volts, the PI level is 3.3v. So you would hook the low side power/ground to the PI. For the ssc side, I only needed...

Testing Our Light Hotspot
Instructions from Helium Light Hotspot with Dragino LPS8 DLOS8 Miner
As our Gateway is now configured to work as a Light Hotspot. We need to test if it is working fine or not, For that, we need to open the staging console from here. Once you have set up a device with a staging console, you need to copy things like Device...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Prepare the adapters and connect them to the terminal stripsThis part is important and tricky, and it took me three attempts to get this right. Here's the rules: Any high-current line must be a twin line that starts as a twin at the power supply's PCB...

Power Gear Assembly
Instructions from 3D Printed Pendulum Clock
This section shows the process of assembling the gears into the frame. There are a few preparation steps that need to be completed before assembly. For now I will just leave it as "print everything and cut the axles to length". More...

Things you will need
Instructions from Modular PSU & Soldering station
Bill of materials(quantity depends on your configuration): Enclosure DPS3003/5 DualDPS3005 PSU moduleMeanwell LRS-100-24Front panel DPS3003/5 or T12 Soldering stationAS-10[IEC320 C14] SocketBS-244DSM-R Red 4mm banana socketBS-244DSM-B Black 4mm banana...

palmPi
Instructions from palmPi
THE SCHEMATICMODSThe Adafruit TFT Friend needs the following modifications: The 3.3V regulator (by 5VIN) must be removed, the 10K resistor next to it must be removed, and the 22 ohm resistor (by CLK) must be shorted out. I also scraped off a bit of the...

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
Installing the LEDs inside the domeOnce you’ve tested all the LEDs, it’s time to mount them inside the dome. But there is one final consideration. The interior of the dome was painted flat black to minimize light scattering. But you’re about to install...

Cartesian Style 3D Printer
Instructions from Cartesian Style 3D Printer
The Frame: I laser cut the frame out of three sheets of 24"x18" MDF. The design is for 1/4" thickness. It could be made out of a different thickness, but your results will vary with rigidity and the press fit tabs will need to be edited. The tabs will...

Replacing the audio samples or config file
Instructions from GPS Talking Clock
Replacing either the audio samples or editing the config file requires re-flashing the ROM chip. Start by making disk image no larger than the flash chip (probably 4 MB). The image should have a standard MBR partition table and a single FAT-12, FAT-16...

Final Assembly
Instructions from VMU Zero V2 [coming soon]
Tools JBC CD1-BB Soldering StationJBC C245-768 Chisel Soldering TipSenju ESC-M705-0.3 Solder WireDesoldering WickDesoldering Pump Parts Assembled PCB (See Instruction #1)Raspberry Pi Zero W (See Instruction #2)Modified VMU Case (See Instruction #3)160...

Installation
Instructions from Remote RasPi GPIO control
Installing This is an application-level program, not a system command or system feature. It is an add-on to your product software, and as such there is no global "apt-get install". You will need a copy of the source to modify for your needs. Step 1:...

Tools and Materials
Instructions from Collapsible UV LED Lamp + Resin Oven
Here is everything I used Consumables: Ultraviolet (UV) LED stripFoil insulation12v 5A power supplyBlue masking tapeClear packing tape18 AWG speaker wire22 AWG stranded wiresolderheat shrinkPCBSize M power connectors(8x) 24" lengths of 1/2" PVC...

Wind the coil and attach the XLR cable
Instructions from Nuclear Magnetic Resonance for Everyone
You need: 24 AWG Enameled Copper Wire. At least 41 meters or 80g 2 meter XLR microphone cable with one M connector (24AWG/0.5mm core) A soldering iron and some solder Ensure that the XLR cable body does not contain any magnetic material. You...

Installation
Instructions from Modern tools for Windows 3.11 software development
You can follow the video tutorial (part 04:24-05:55), or follow written instructions. To start, you need to: download the latest release of IDE package from GitHub: https://github.com/adbrt/cb-legacy-dev/releasesit will contain the installation script,...

1
2
3
4
5
>
>|