179 Results for "solder fume extractor"

Resistor 100k
Instructions from BioAmp v1.5
Solder 2 x 100k resistors at R9 and R10.

Resistor 220k
Instructions from BioAmp v1.5
Solder 2 x 220k resistor at R3 and R4.

Wiring the matrix (columns)
Instructions from FPGA Blinker
Now, solder 8 wires between C'x and G"x. Calculate the appropriate current limiting resistors values and have them handy (do the calcs and buy them beforehand). Solder the resistors on the borad and use wires to solder the PMOS drains (D'0, ..., D'7)...

Top wiring 3: Ground connections
Instructions from Adaptive wireless switch
Top half of case. There are two ground wires on the LiPo charger. Stretch one over to the large circular area of the keyfob. (See photograph in Step 14.) Cut to length, strip it and solder it to the circular area (in common with the black wire of...

Arduino Game Console - the BlueOkiris Gameduino
Instructions from Arduino Game Console - the BlueOkiris Gameduino
Take the analog stick and solder the appropriate wires to it. Place ground to ground, 5v to 5v, x to A4, and y to A5. Again do not use male ends to the arduino.

Resistor 10k
Instructions from BioAmp v1.5
Solder 6 x 10k resistors at R1, R2, R5, R6, R7, and R8.

High side drivers (current sources)
Instructions from FPGA Blinker
Repeat 8 times: take a BS250P PMOS and solder the S, G and D pins to the board (S to the Vcc bus) and a 10K resistor between the G and the S (or the Vcc bus). Let's label the Gs and Ds (G'0, D'0), ..., (G'7, D'7), respectively. Take a BS170 NMOS and...

Install the Teensy 3.2 and the Potentiometers
Instructions from IBM Thinkpad 380ED Keyboard/Trackpoint to USB
Use a Teensy 3.2 with header pins or solder your own header pins taking care to get them perfectly straight. The surface mount connections on the back side of the Teensy can be done with flying leads but a 2 x 7 SMD header is a lot easier to install....

Animated Led Brake/Turn signals for RC and Esk8
Instructions from Animated Led Brake/Turn signals for RC and Esk8
Test fit components to measure pcb size.Be patience and take your time place all the parts in a small footprint. about 30mm x 12mm is what I ended up with, very small.take note of the order, this can make some parts much easier to solder.

Third Eye for The Blind
Instructions from Third Eye for The Blind
Making the ModulesFirst cut the pref board in 5 X 3 cm dimension and solder the female headers for the arduino to the board.Then solder the buzzer.Then connect the vibrating motor using the glue gun and solder wires to it.Then connect the LED.Then connect...

Prepare the Tools
Instructions from Edgerton, A High-Speed LED Flash
Be sure to have the following tools ready: 3D printer with 200mm x 200mm bedSoldering iron & solderSmall side cuttersHot glue gunAllen wrenchesDupont crimper kit (optional but recommended)

Prepare the cable
Instructions from EXPS/2
Add a solder blob on each pin of the DIN-13 connector Solder the wires following the color code/pinout on the schematics. Start from the lower and use heat shrink tubing on each wire. Solder the cable shield to the connector shell taking care to not...

Assembling the PCB
Instructions from Solar Powered WiFi Weather Station V3.0
After receiving the board from the PCB fab house, you have to solder the components. For Soldering, you will need a decent Soldering Iron, Solder, Nipper. First I cut the straight male and female headers pin for ESP32 Board, TP4056, BME280, and jumper...

Build for Cooling
Instructions from Battery Desulfator Kit, TESLA 12V compatible
There's a free license version of Eagle Cad for viewing/printing/exporting gerbers etc. Otherwise in the gallery you'll see a schematic and a layout guide.The FETs and the Snubber Schottky are laid out along the edge of the PCB for direct mounting to...

Portable Altimeter Logger with Display
Instructions from Portable Altimeter Logger with Display
First thing we need to get the components!1. You can pick up a 3V Pro Trinket at http://store.hackaday.com/products/trinket-pro-with-black-solder-mask-and-the-hackaday-io-logo or Adafruit $10 (3v not the 5v since the BMP 180 needs a vcc of 3.3v)2. BMP...

|<
<
1
2
3
4
5
>
>|