166 Results for "soil+sensor"

IoT Smart Lobby - Welcoming Music System
Instructions from IoT Smart Lobby - Welcoming Music System
Step 4: SET UP YOUR PIR SENSORAs you can see, next to your sensor’s pins are small indications on what each pin is made for:D is for Data+ is for the current connection- is for the ground connectionSimply connect as in the picture below to set properly.For...

Mount electronics
Instructions from Cat Detector - Useless Machine
I drilled 1/8" holes for screws in my enclosure, and then countersunk each hole with a larger drill bit so the head of the screw would be recessed. I used (5) M2.5 x 10mm standoffs and (10) M2.5 x 6mm screws to mount the Arduino Uno and the Microphone....

The Dragino IoT Kit
Instructions from LoRaWAN using Dragino Gateway and TheThingsNetwork
The Dragino IoT Kit is a well-designed kit to facilitate beginners and developers to quickly learn LoRa and IoT Technology. With the help of this kit, you can make a lot of LoRa based project and also learn about the IoT applications of LoRa. This kit...

Lidar
Instructions from Earth Rover
Generate distance map. Install pan mast —> CompleteImplement pan Arduino command: 13-14 —> CompleteInstall pan and tilt mast —> CompleteInstall PWM Board. —> CompleteInstall Lidar sensor —> CompleteImplement Read Lidar Arduino Command: 15 —> CompleteImplement...

DIY Smart Home Security System for <$50
Instructions from DIY Smart Home Security System for <$50
Step 3: SET UP YOUR PIR SENSORAs you can see, next to your sensor’s pins are small indications on what each pin is made for:D is for Data+ is for the current connection- is for the ground connectionSimply connect as in the picture below to set properly.For...

Square Foot Gardening
Instructions from Square Foot Gardening
Building and setting up the garden box1. Buy the lumber and supplies. I got everything at Lowes in one trip for a total cost of about $150. Soil is expensive as it turns out. - pro tip on the lumber, the 16 foot long is the cheapest, and you get a 45"x...

Measurement of Stripe Pattern
Instructions from Getting Cozy with the Diffraction Limit
To check the diffraction limit, a simple stripe pattern was displayed in the image area of the monitor. The stripe pattern was 101010… across each row. Figure 8 Stripe Pattern. After color gain, and spatial jitter removal, multiple images...

Step 2: 3D Printed Parts and Mounting the Electronics
Instructions from EMT Conduit-Mounted Wind Sensors
To mount the electronics to the EMT conduit, I designed several custom 3D-printed parts, all of which can be found for free to download from Thingiverse (links are below): 2 x Wind sensor mount 2 x 1/2" EMT conduit side-to-side clamp 1 x 1/2" EMT Solderless...

FarmBot - Open-Source CNC Farming
Instructions from FarmBot - Open-Source CNC Farming
Supporting InfrastructureFarmBot Tracks need to be attached to supporting infrastructure. Where you decide to install your FarmBot will determine how you setup your Tracks and therefor what supporting infrastructure you need. You might attach your track...

GPS controlled FischerTechnik Clock
Instructions from GPS controlled FischerTechnik Clock
2:1 acceleration and minute sensor.It's very difficult to make a DC motor run at the exact right speed so that some axle goes around at a certain speed (e.g. once a minute for a second hand in a mechanical clock). There are 86400 seconds in a day, so...

How to Make Color Sorting Machine Arduino Based
Instructions from How to Make Color Sorting Machine Arduino Based
Story In this tutorial i will show you how to make a simple color sorting machine machine using Arduino and TCS230,TCS3200 color sensor with servo motors. In this project Color sensor detect the color of candy and generate output in this output sensor...

CIS Reverse engineering Part 1
Instructions from Magic Frame : Turn Everything into a Touch Area
As Wikipedia is way better than me on explaining :"Contact image sensors (CIS) are image sensors used in flatbed scanners almost in direct contact with the object to be scanned. Charge-coupled devices (CCDs), often used for this application, use mirrors...

here are some instructions. a faq page will be added to github once i look thru some of the questions
Instructions from mlx90640 sensor works w 800 bytes
download code here https://github.com/jamesdanielv/thermal_cam_mlx90640 it should contain a file called MLX906040_example32ataTime.zip the code inside should take one row of data and output it to terminal. if this works you have your sensor working ok....

Assembling the PCB
Instructions from Solar Powered WiFi Weather Station V3.0
After receiving the board from the PCB fab house, you have to solder the components. For Soldering, you will need a decent Soldering Iron, Solder, Nipper. First I cut the straight male and female headers pin for ESP32 Board, TP4056, BME280, and jumper...

Bill of Materials
Instructions from Mindful Droid - Take Action against Air Pollution
PCB Design and Electronic Part List PCB Board DesignArduino, MKR WIFI 1010 - 176-3647Seeed Studio Air Quality Sensor v1.3 Grove System, Indoor Air Quality TestingMQ-7 Gas Sensor (Carbon Monoxide) × 1High Capacity Lithium-Ion Battery Pack (6700mAh)...

|<
<
1
2
3
4
5
>
>|