137 Results for "soil+sensor"

Soldering the Headers
Instructions from Solar Powered WiFi Weather Station V3.0
Plug all four headers into the PCB. The PCB is labeled to identify which header goes to which place. The male pins of the header should enter the top side of the PCB and extend out the bottom. I always solder two-end pins first, then solder the remaining...

Hopper Assembly
Instructions from Bloft Mk2 - 3D printer for plastic waste
Now we start adding the components for the material feeding system. These include the hopper, the hopper inlet and the joint body that connects the hopper with a material reservoir. There will be also a motorized feeding system. Prepare: 6 pcs M3 Square...

Step 8: Installing Personal Weather Station
Instructions from IoT Personal NodeMCU ESP12 WiFi Weather Station
The location weather station is the most important part of installation. If weather station is located under a tree or an overhang, the rainfall data measured by the station will not be correct. If you place your weather station in an alley, you could...

Run a Program
Instructions from Measure water Flow Rate using Arduino & Sensor
volatile int flow_frequency; // Measures flow sensor pulses// Calculated litres/hour float vol = 0.0,l_minute;unsigned char flowsensor = 2; // Sensor Inputunsigned long currentTime;unsigned long cloopTime;#include LiquidCrystal lcd(12, 11, 5, 4, 3, 9);void...

Adding Buttons (Optional)
Instructions from Exercise Bike to a Wireless Gamepad [ESP32]
In case your exercise bike does not have sufficient buttons/touch pads to interact with the game, you can add buttons. In the below image I have added a joystick, a d-pad that also acts as XYAB buttons, and also LB and LT buttons which are housed in...

Assembling the fermenter
Instructions from An open-source fermenter
Now that you have fabricated each element of the fermenter, it is time to assemble it! Below you will find the assembly strategy. Gather the different elements and bring your Allen key and the bolts and nuts referred to above. Please also refer to the...

Designing the System
Instructions from Smart Coffee Machine Pump
System’s Logic The system is designed with the following simple logic in mind: The system constantly monitors the distance between the sensor and the water surface.Whenever a change in distance goes over a threshold value, the system sends information...

Calibration
Instructions from E-TKT: anachronic label maker
This final part of the process will make sure the letter alignment is finely adjusted, and together with the correct imprinting pressure. « attention is needed here, please » reboot your E-TKT;after the splash screen the machine will...

Choose what modules you want in there
Instructions from Fancy Power Strip
I modified two power strips. Once has the IR ToF sensor module (H08R60) to replace its power switch so that you can use hand gestures to turn on/off and the other one has a BLE and a USB modules so that you can control it via a smartphone or connect...

Imaging and Reconstruction
Instructions from Getting Cozy with the Diffraction Limit
The next step is to attempt to recover the image. The image area in total is 48x48 monitor pixels. The 48x48 image is made up of a 24x24 image of interest, and a 12 pixel border of random values. Figure 15 Image of interest with random...

Multipoint Algorithm
Instructions from Magic Frame : Turn Everything into a Touch Area
As I was saying, the multi-point cannot be perfect using a light triangulation technology with a CIS sensor. It is pretty complex to work on this part... But it is also very fun to imagine many different solutions on how to have the best results without...

Acquire Parts Needed
Instructions from Optimote | Bio-Adaptive Media Controller
Step 1 Get Parts Needed You can find all the necessary parts on eBay. Here are a few links; Pulse Sensor Amped Arduino Pro Micro 5v 16MHz SPDT Slide Switch - Through-Hole 3 Pin - Only needed if non-software mode switch is desired. Soldering Iron...

Summary
Instructions from Grasp Bionic Hand
Assembly steps Printing and removing support material Fingers assembly Thumb assembly Inserting the motors on the palm Inserting the motor on the thumb Fingers and palm assembly Casting silicone in the molds Gluing the silicone “skin” in...

Configure AdafruitIO
Instructions from Visualise data from WiFi sensor without coding
Go to AdafruitIO account or register (io.adafruit.com) if you do not have one. The account is free of charge with some limitations. However, for this project the free account is sufficient. > Create a Dashboard and name it e.g. MyHome > In...

The NanoStillery™ - Whiskey Distillery
Instructions from The NanoStillery™ - Whiskey Distillery
Electrical Schematics and Parts Electrical parts:DS2 DS18B20 1-Wire Temperature Sensor Probe Cable DS3 DS18B20 1-Wire Temperature Sensor Probe Cable DS4 DS18B20 1-Wire Temperature Sensor Probe Cable DS5 DS18B20 1-Wire Temperature Sensor Probe Cable IC1...

|<
<
2
3
4
5
6
>
>|