819 Results for "≡ 예약문의 OIO《⑧④89》83ⓞ⑥ ≡선릉드림레깅스룸☜드림레깅스룸dreary강남드림레깅스룸선릉드림선릉드림레깅스룸distinct 강남드림㈓ゲ선릉드림레깅스룸선릉드림summit"

TrinketPro Movement Alarm for Bag Theft Prevention
Instructions from TrinketPro Movement Alarm for Bag Theft Prevention
Step 1: Gather your componenetsObtain / purchase the following components:1x Trinket Pro. You can get one at the Hackaday store.1x Accelerometer. You can use a variety, but I used the GY-521 available here. 1x Project box. I used a project box with an...

TrinketPro Movement Alarm for Bag Theft Prevention
Instructions from TrinketPro Movement Alarm for Bag Theft Prevention
Step 3: Plan how to lay out the components on the boardI had to think about how to lay out the board. The board I used came with the project box, which you can see here:The schematic of the project is here:And a picture of how all the components are...

TrinketPro Movement Alarm for Bag Theft Prevention
Instructions from TrinketPro Movement Alarm for Bag Theft Prevention
Step 4: Cut the perf boardThe easiest way to mount the buttons was to cut a piece of perf board the same size as the end piece for the project box.To do this, I traced out the piece from the project box on a piece of perf board:And then cut it with a...

Trinket Watch
Instructions from Trinket Watch
ButtonsNow you can set aside the microcontroller and display assembly to work on the navigational buttons. Set them up on a piece of PCB protoboard like so:One side of each switch will be connected to ground, the other to a digital input pin. So run...

Car of the future!
Instructions from Car of the future!
Monitor prepOpen monitorRemove screen and cable from headrest housingcut perimeter of plastic housing to be able to drop it farther backremove cut out pieceremove foam backingdremel notch at bottom to allow newly formed backplate to go all the way inhot...

12V work light
Instructions from 12V work light
prelim. assemblyScrew light in place with bolts, washers and nuts. Cut a small piece away from the U frame ( not done 100% in the pic) to prevent legs from rotating:

Beat This
Instructions from Beat This
Cut a small piece of aluminum less than the thickness of your headphones. Then bend in a vice slightly till you reach your deisred bend.Cener and drill 1/8" holes in alumionum and headphones to match.Rivet the plate to the headphones.Bend to desired...

µBob biped robot
Instructions from µBob biped robot
The feet are cut out from a piece of plastic and simply glued to the leg servos.

Humidity/Temp Controlled Power Outlet
Instructions from Humidity/Temp Controlled Power Outlet
Rough Code so far... Was able to get it to verify in the arduino IDE. I had a photo sensor tutorial in my arduino starter kit and was able to piece together part of the circuit. Right now i have another test sketch which turns on an LED to indicate day...

DIY Metal PCB Solder Paste Stencils
Instructions from DIY Metal PCB Solder Paste Stencils
7- Remove the vinyl from the cutting sheet... Peel the backing from the vinyl and adhere it to a piece of aluminum flashing cut to the size of your board...

Dollarstore lens find = Big screen Cardboard
Instructions from Dollarstore lens find = Big screen Cardboard
Design 1: Don't make the viewing tube too big... you want the phone to be a bit bigger than the hole.Easy to adjust lens distance to phone - lenses are mounted on separate piece of just the right height and folded to width for stability.

Putting LiPos into your MIP robot v2
Instructions from Putting LiPos into your MIP robot v2
To make room for the LiPos, you need to cut away the interior parts of the plastic. You can use a dremmel, but a scalpel does a good job of getting into the tight corners. Scalpels are super sharp and easy to snap, so be careful.Take a look at the picture...

Heartbeat Sensor Tutorial
Instructions from Heartbeat Sensor Tutorial
Troubleshooting If you are having issues detecting heartbeat with your MOD, there are a few things that might be causing this error. SPIT ON IT. First, make sure you have good electrical contact. These sensors are made to be worn while sweaty, but if...

Wine not shed some light?
Instructions from Wine not shed some light?
7. ASSEMBLE THE FIRST T PIECEMeasure the distance you want the bottle to hang down and roughly mark on the cord.Slide the straight reducer over the cord, smaller end facing the bottle. Put a cable tie on the cord to set the height.Strip the outer insulation...

Wine not shed some light?
Instructions from Wine not shed some light?
8. ASSEMBLE THE REST OF THE PIPEWORKThis part took a bit of thinking/tinkering/trialling. You may find an easier way to assemble it but this is the order that we did it.Attach the first complete bottle T you made with a nipple, another T (that faces...

|<
<
3
4
5
6
7
>
>|