1621 Results for "%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EA%B0%95%EC%B6%94%E2%9C%9Awww%2Coptime4.com%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%20%EC%9D%B8%EC%B2%9C%EB%A7%88%EC%82%AC%EC%A7%80%20%E2%9C%9A%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%E1%98%9B%20%EC%9D%B8%EC%B2%9C%EC%98%A4%ED%94%BC%EC%82%AC%EC%A7%84%E1%98%9B%20%EC%9D%B8%EC%B2%9C%ED%9C%B4%EA%B2%8C%ED%85%94%20%EC%9D%B8%EC%B2%9C%ED%82%A4%EC%8A%A4%EB%B0%A9%20%ED%83%80%EC%9E%84"

This is a GitHub project
Instructions from RPI, Win, Unix Object (Vehicle) Speed Tracker
Setup Requires a Raspberry Pi computer with a RPI camera module or webcam installed, configured and tested to verify it is working. I used a RPI model B2 but a B+ , 3 or earlier will work OK. A quad core processor will greatly improve performance due...

Installation of build requirements
Instructions from MQTT2LoRa Bridge
Change to the directory /opt and create a directory named libraries for the needed libraries. Change the owner of the directory to pi to get unrestricted access to the directory and the directroy under it. cd /opt && sudo...

SOLAR POWERED ARDUINO WEATHER STATION
Instructions from SOLAR POWERED ARDUINO WEATHER STATION
2. Making the Receiver :The receiver module receive the weather data by a RF receiver and it is processed by Arduino UNO .The processed data is displayed through a 20x4 char LCD display.You can also choose a 16x2 LCD also.The main reason for using a...

Turn on and Troubleshooting Notes
Instructions from Flea-Scope USB O-scope (18 Msps, $13 BoM, WebUSB)
I first visually look for shorts/opens, especially on the QFN or QFP and USB (shorts can be easily reworked with the Kester 2331-ZX flux pen; always clean and dry boards after rework; I use isopropyl alcohol and a toothbrush followed by running water)....

Simple digital watch
Instructions from Simple digital watch
Wiring the displayTo Wire the display you just need two wires for communication because it uses a I2C protocol and two for power so 4 in total. The two wires for the communication need to go to pin A4 and A5 and power to power. The wiring:A4 - SDAA5...

Math
Instructions from Electric Heart
With the information from the previous step in hand, you'll now need to calculate your oscillator frequency. In order to do so, you'll need to calculate the minimum possible frequency with the equation which rearranges to and the maximum...

DNA Lamp
Instructions from DNA Lamp
Choose your color pairsWe will use one color for each nucleobase. Remember that nucleobases go in pairs, and that the only possible pairs are adenine-tymine and guanine-cytosine, so if you don't want your annoying bio-engineer friend to make sarcastic...

Installing Arch Linux
Instructions from Liberating a $50 Windows Tablet
During your normal Arch installation you usually come to the point where you install the bootloader. In most cases either GRUB or systemd-boot. We will install GRUB.For the following commands I assume, you have arch-chroot ed into the installation.I...

Solder the QX5252F
Instructions from DIY SOLAR SOLAR LAMP
The QX5252F comes in TO-94 package, the space between the adjacent legs are very small. So extra care must be taken during soldering. Otherwise, you will short the pins together. In my V2.0 PCB, I have used the TO-94 package footprint, but in V3.0 I...

Main amplifier
Instructions from Low-cost EEG circuit
Once the DC contribution has been removed from the signal, an operational amplifier can be used to amplify it by a factor G tunable by changing the value of R9 and R10, furthermore, by adding a capacitor C5 a low pass filter...

Manual SMT Pick and Place Machine
Instructions from Manual SMT Pick and Place Machine
The Arduino code is incredibly simple, with some strange looking oversampling for preventing the motors from vibrating:void sampling() //Oversample the slider readings to avoid motor vibration. { i=0; val =0; smallVal=0; while(i

D.I.M.E.R PROJECT 6 DOF Robot Arm
Instructions from D.I.M.E.R PROJECT 6 DOF Robot Arm
Hello there!In Christmas I had a little more time to improve DIMER, improvements have been mainly two; motor drivers and two potentiometers to know their position and power programming.Drivers:In Bilbao maker fair another maker told me he had just found...

Conclusion
Instructions from Weather Dashboard with Dark Sky API
Go to your Initial State account and look at your data. I changed all my percentage values to arc gauges, the precipitation to a liquid gauge, and the temperature to a temperature gauge. You can change to any kind of Tile types and choose your colors...

Bonus! Long-Range RFID Control
Instructions from Long Range RFID Controlled Dry Cleaner
When we got the conveyors, they also gave us thousands of dry-cleaner slips, and this beautiful device to organize them. How cool would it be if we could use the actual slips to command the machine around?Turns out there is some brand new consumer-level...

Wiring Up the Circuits
Instructions from Nunchuk Controlled Robotic Arm (with Arduino)
Once the structure is assembled, and Nunchuk connectors are finished, you'll be ready to wire up the circuits. I used the controll board shield that came along with my robotic arm kit. It makes the connection of the components easier, since it already...

|<
<
5
6
7
8
9
>
>|