Close

451 Results for "《〈 문의 OIO↗5793↗7458 》〉 강남셔츠룸ㅬ レresidence㎱강남셔츠룸신사셔츠룸⑧appetite 강남셔츠룸강남란제리 강남셔츠룸╃강남란제리″names㏊"

  • Building the thrust testing rig, part 2
  • Log     from GimbalBot
  • I did a bit of assembly work today on the thrust testing rig. First thing's first: I needed to cut down the prop nuts (there must be another term for these) since I need the motors as close together as possible:I filed the cut edge down a bit, but I...

  • A few on-the-fly changes...
  • Log     from GimbalBot
  • It's a hacking project, right? That means unexpected last-minute changes! Also, lots of updates that lack significant progress. Oh well, one step at a time.First of all, I apologize for the quality of these pictures. My cheap but effective camera seems...

  • X and Y Mechanics Completed, Partial Z
  • Log     from Laser Cut Mini Mill
  • I finished cutting most of the wooden parts and assembled them, I cut all of the linear rod and the remaining threaded rod. Most of mechanical assembly is complete. I put together an end stop based on the DarwinOptoEndstop for the X axis and hooked up...

  • Completed X,Y and Z
  • Log     from Laser Cut Mini Mill
  • I finished assembling the Z carriage, I had to reduce the flange on the anti backlash nut for the Z axis to fit the space in the carriage. Mounted a temporary end stop for the Z axis, it limits the travel a little bit but it will work until I can...

  • Dremel Mounted and First Cuts
  • Log     from Laser Cut Mini Mill
  • I finished the first iteration of the Dremel mount (added to GitHub), while doing that I found a couple more changes to the Z carriage that I want to make. The Z Carriage needs to be about 6mm taller, it doesn't currently clear the Z stepper motor, so...

  • Aluminum Test
  • Log     from Laser Cut Mini Mill
  • I haven't had a lot of time to work on this, but yesterday while I was doing something else I put a piece of 1/4" aluminum on it to see what happens. I wasn't expecting it to work, I assumed it wasn't rigid enough to actually mill the aluminum, but it...

  • Plumbing
  • Log     from Unity Candle
  • Several pictures of the nearly finished plumbing.  The first is of the accumulator tank end:The accumulator tank is at the bottom.  I sourced a new, purged and never used LP tank from the hardware store to remove worries of residual propane...

  • Electrical for testing
  • Log     from Unity Candle
  • In the prior post I discussed the plumbing.  At the bottom of the first picture were two boxes.  The black one at the base of the accumulator contains connections and relays to remote control the system.  I  knew I needed remote control,...

  • Controller Modifications
  • Log     from Unity Candle
  • I probably could use the paddle board pretty much as is, and reprogramming the existing SC87C451 microcontroller. There look to be extra GPIO pins available that I could use for my other required inputs and outputs. That said, I don't have the tools(compiler...

  • Not So Rapid Prototyping
  • Log     from Goliath - A Gas Powered Quadcopter
  • I haven't been posting build updates as frequently because the build activities have mostly consisted of sanding....lots and lots of sanding.  The good news is that I'm nearly complete with the first flight quality propeller!  I've talked previously...

  • Powder and Dispenser
  • Log     from Upcycled Full Color 3D Printer
  • Powder tried:PowderResultPlaster + Talcum powderNot enough strength both immediately after print and after settingPlaster + sugar + dextrinIncrease wet strength, but very difficult to spread. Also very messy.Salt + dextrinGood wet strength, improved...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday