6309 Results for "《 예약문의 OIO↗8489↗8306》가라오케┦가라오케world선릉가라오케가라오케사이즈청담가라오케promotion 선릉가라오케┫ ∫선릉가라오케decided"

HydraNFC Firmware is coming
Log from HydraNFC Shield v1
HydraNFC Hardware: Schematic in PDF and CADSOFT Eagle 6.x design (CC BY NC) will be available (HydraNFC github) at same time as HydraBus will be in shop.HydraNFC Firmware (requires HydraBus) with VT100 and Autonomous mode (requires only power through...

HydraNFC board, BOM and doc available on github
Log from HydraNFC Shield v1
HydraNFC GitHub Repository: HydraNFC_1_1_Rev1: HydraNFC Shield Schematic and Board CadSoft Eagle 6.x HydraNFC_Antenna_1_0_Rev0: HydraNFC Antenna Schematic and Board CadSoft Eagle 6.x All those boards and BOM are now available on github: https://github.com/bvernoux/hydranfc/tree/master/hardware...

Finally Acrylic is in hand
Log from PixelWand
I stopped by Tap Plastic to get some Acrylic. I bought 4ft x 4ft piece cut in half so that I can fit it into my laser cutter. I have time scheduled on Tuesday to use the cutter, so I'm ready.Since I still had a couple of the test pieces left,...

Frame Assembled!
Log from Simple DIY laser cutter
Well the design worked pretty flawlessly. The frame bolted together quickly and easily and is just waiting on the OpenRail to arrive to finalise the frame. I will still need to undo a few sections to attach brackets and bearing blocks but...

A small design change.
Log from Simple DIY laser cutter
I have decided to flip the X axis stepper on top on the X axis. The reasons for this are I cut out needing 2 idler pulleys and the motor mount can be simplified meaning both motor mounts are the same! Although I lose a little X axis...

GT2 Belt clamp design.
Log from Simple DIY laser cutter
I finally got around to designing the belt clamps that will attach to the bottom of my X axis gantry plates. This is a simple design and will only require 2 screws to keep the belts tight and in place.I will be machining these out of HDPE.

Two-core Fluxgate
Log from DC Current Transformer
My last project entry described a single-core fluxgate, and showed that it can measure primary currents. It also showed that the fluxgate injects a few hundred mV of ripple into the primary circuit. This entry describes a two-core fluxgate which offers...

Pulse Generation Circuits
Log from DC Current Transformer
In the last posts we saw how a fluxgate works in simulation. Simulations are all good when you can just add a pulsed voltage source - everything is perfect. In the real world, we have some challenges:1) We need very low DC offset to avoid...

Care and Feeding of MOSFET Bridges
Log from DC Current Transformer
In this entry we'll look at how to deploy MOSFETs in bridge circuits. (This is also applicable to IGBTs.)Switch mode electronics are great - they are usually smaller and more efficient than similar linear circuits. However, there are some limitations...

Testet the X Axis
Log from Homemade PCB-Mill / Laseretcher
First Test of the X-axis was succesfull. The axis don't have a belt at the moment, because they didn't arrived at time, but a sholace will works fine ; ). Next step is to Design the new holder for the y-axis linear shafts, with a included beltholder....

Mounted the motors outside
Log from Homemade PCB-Mill / Laseretcher
Now the Motors for the X-Axis are mounted outside, so the Working-Area gets bigger.

Galaxy S4 AMOLED screen working
Log from MIPI DSI Display Shield/HDMI Adapter
We have a working Galaxy S4 AMOLED screen, 1920 x 1080. A QHD screen from GS Note 4 is waiting to be tested soon!

Set the stage, cue the music
Log from Coming soon...
I have always wanted a robot arm. Youtube Kuka and you'll understand. So in college after building my Photovore (see "things I've built" section of my profile), I bought some servos, wires and the Lynxmotion SSC-32 Servo controller (and arm control software),...

Finished the Panel Graphic
Log from Port-a-Pi Power Supply
I finished designing the panel graphic. The hole for the LCD is 2.5" by 0.75". The hole for the switch has a diameter of 0.5". The graphics are an edited version of the Raspberry Pi logo and line art of Marisa Kirisame from Touhou.

Pi Supply added
Log from RaspBox - Home Automation & Cloud
Just a small project log to say that I've installed a Pi Supply on my Raspberry Pi in order to bring ATX-style power supply to it. The Pi Supply website gives a script to run on the Raspberry Pi to detect a button press from the Pi Supply and halt...

|<
<
3
4
5
6
7
>
>|