12981 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

VGATonic Road Map
Log from VGA Graphics Over SPI and Serial - VGATonic
Most everything I've got planned involves the Atmel silicon onboard, the ATTiny 2313a.The ATTiny is the (128 Byte) brains of this setup - it has a Universal Serial Interface which I am using as SPI. For the early demo, the first thing the board does...

DISASSEMBLE JOHNNY FIVE
Log from 3D printer brain retrofit
Sexy upskirt photos of disassemblyOuter housing offBlurry shot of the inside w/ 3 pcbs removedlaid out on the table, next to the smoothieboard (on the right)everything outFront panel, begging to be replacedBack end of the extruder and thermocouplesSmoothieboard...

Getting started
Log from Flight Simulator Radio Panel
Ah, the smell of a new project. Everything fits together perfectly on paper, and no real-world obstacles have been hit yet.As far as communication with Flight Simulator X, it has an API for 3rd-party integration (SimConnect), but I haven't been able...

Got Some 74173 and a schematic, plus a plan
Log from SBP-CPU (Slice Based Processor)
My 74173s came in the mail today. Tested and working, so I came up now with a plan to make everything and I have a preliminary design. First a picture of my new parts:This is basically where I tested and my current setup. Don't worry, I have plenty more...

I am back
Log from Printing bones on a DIY powder bed 3d printer
On monday I have received the results of the exams I had in past two months. This also concluded my high school days and started my almost 3 months long break. This means I will have a lot of free time to work on this project. Even though I had final...

After playing around with the board for awhile, a few other changes that I would make
Log from 1284P-Target
Overall, I think I didn't do a half-bad job on the board but there are a few more things that I would change in addition to a reader's suggestion of dedicated headers for I2C and SPI:Move the crystal and its capacitors a little further...

Getting MUCH smaller with more features
Log from Thunder Pack
The new prototypes have arrived!The board now features a 16Mb SPI flash chip and DotStart Micro RGB LED (APA102-2020). These additions were inspired by CircuitPython. The flash chip gives much more space for your python programs and the LED is used...

First PCB tested
Log from Open FFBoard
Finally the first pcb arrived and is tested to find any errors in the design and see if there are any major issues. Soldering everything by hand takes some patience but everything works as it should. A few problems spotted in the first design: 1. Vias...

uECG instruction update
Log from uECG - small open source wireless ECG sensor
While the shop is in last stages of development, we uploaded a new instruction for uECG! After sending first devices to Ingiegogo backers, it was time to seriously update the instruction section, cause it only contained information about the firmware....

All-in-one prototype
Log from Project Healing Heart
So much has happened since the last log!In this log, I'm documenting the steps I took to assemble everything into one piece with the heart prototype. As you can see in the video below, all 4 LEDs are currently working and the Arduino is still able to...

Final version, project complete
Log from linear bench psu
Just finished building, programming, and testing V3.Here's some photos.Lots of lessons learned with this project. The schematic does not represent the final design. The biggest change is changing the feedback to be at 1.1v maximum for current and voltage....

Testing Rev 3.0 Prototype
Log from All-In-One Gamma-Ray Spectrometer
Some parts came earlier than expected. Enjoy this sneak peak of a revision 3 PCB that I'm currently testing. Same board footprint, but much better layout and silk screen due to 0603 components. Also, there are less (confusing) jumpers and a breakout...

Dismissing the "new arch", the EVB, and Bitter fighting with Linux drivers (2022-10-09)
Log from Linkia
Original date: 2022-10-09 Related tweets: [1] [2] [3] [4] [5] [6] [7] [8] Dismissing the "new arch" Since the suspend-to-RAM works perfectly on the latest X1000 SoM, there are no strong reasons to keep a separate "EC" MCU anymore. But unfortunately I...

From Inception to Now
Log from Small Car EV
This blog is being transferred from my own website to Hackaday so this post is going to serve as a summary of progress from inception to present-day. Earliest post Since I'm starting from scratch and I don't know anything about go-karts, I decided to...

Building the thing...
Log from DIY Spot Welder for Creating Battery Packs
In order to weld metal to metal with a spot welder two things are important: a certain pressure onto the material with the electrodes to establish proper conductivitythe time it takes to weld the material The first bit can be achieved by hinging both...

|<
<
5
6
7
8
9
>
>|