Close

2368 Results for "《 예약문의 OIO≡⑧④89≡83O⑥》강남레깅스⒴선릉레깅스룸allowed⑧레깅스룸선릉레깅스룸선릉레깅스badly 레깅스룸견적㎸레깅스룸견적♤ⓩ강남레깅스provisions"

  • Wave Shield - Take 2

  • Since the volume of the first test was so dismal, in part due to the poor speaker and open air conditions, I whipped up an amplifier from an LM383.  8w baby!  You can sure hear it now!  Oh, and I'm sure the better quality speaker and enclosure...
  • First Post

  • After creating a typical MSGEQ7+Arduino+WS2812 music visualization display and successfully taping the pieces, including breadboard, to the wall for a party, I decided I'd go all in on a more refined solution.The original goals were to:a) Run a FFT instead...
  • Enclosure

  • ** log in progress **It took a lot of napkin sketches to come up with an enclosure that I liked for the wall-mounted LED strip + PCB assemblies as I didn't want to slap a rectangular box on the wall and call it good. I ended up designing a nifty 3-layer,...
  • Design Changes

  • Okay, so honestly I'm attempting to do a large amount of work with D-DAQ being so small. A little ambitious, yes. By nature of that, I've not gone into looking at every fine detail of every component and every function simply because my head would explode.----------...
  • Back to work!

  • I didn't realize how much of a sprint I was in leading up to the Hackaday Prize Phase 1 submission deadline. Looking back through the project, it's a bit nuts to see how many log updates I put together in July and August. The break has given me a bit...
  • Suddenly, A Wild L319 Appears!

  • This one is/was a fire truck with a big gasoline engine. You can tell this based on the motor hood (additional cooling slots, (closed) hole for water pump), the flippable stairs on the side and the flat rear.Other news:Sping just came around the corner...
  • 1.3 New Designs

  • As much fun as this has been to play around with, the print area is just too small! Using SketchUp I've come up with some designs for a new scaled up version using MakerBeam and pulleys (instead of threaded rods like current design). This...
  • Challenges issues and accepted

  • I am considerign useing the ta-200 enclouser that is commonly used for remote SSR curcits in many hobbly level stuff. There nice and cheap $6-7 each and they make a nice standard to work with. But it is a small case i need to knwo if the wires even fit,...
  • Enclosure

  • I borrowed an idea from my friend Mads Hobye for my enclosure. Mads founds these sleek boxes at the container store and used them to make project enclosures for the various musical instruments he's built. These boxes are particularly convenient because...
  • Big Teensy Adventure!

  • Welcome to the Teensy USB Development Board Bragging Project Log. My Teensy 3.1 was just delivered, and I love it so much that I am dedicating this project log to unboxing and testing.I ordered it direct from pjrc.com. Pictured below it arrived in its...
  • Update March 2015

  • I have been very busy with other projects and have not touched YHM in a while. I have done some testing at the mailbox and found that the XBEE range was not good enough, +/- 30m but there are walls etc. in the way. (My XBEE modules use the onboard chip...
  • Not dead yet

  • Despite having been quite for the last ~2.5 years I finally got around to making some progress on this project. I've got the initial control circuitry rigged up, a mega328 board acting as the controller with a RTC to provide the timekeeping functionality...
  • Power savings success

  • Just got the latest revision from the fab. Using a low side MOSFET switch does indeed turn the power usage down to unmeasurable levels. There are a few considerations.You must disconnect the trigger pin by setting it to an input (and setting it back...