2313 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워레깅스룸Ｉ ↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ ォfatalㄿ강남쓰리아워쓰리아워⑾westminster 쓰리아워가격강남쓰리아워 강남쓰리아워モ강남술집정보ㅥgotㅸ"

Low cost Smart Switch
Project by Thomas Flayols
Control and monitor any lighting setup : a low cost 1-Wire module.
- 59
- 35

The PCBs arrived...mistakes where made
Log from GNSS module 2.0 - GNSS via Bluetooth
The PCB arrived and they look perfect, not that I had any doubt when ordering at a big Chinese manufacturer. And of course there are mistakes :/ The voltage regulator for USB power to the GPS chip U5 has the wrong footprint. I used a SOT-89-3 foot...

Cost optimization, run 1
Log from Arduino Compatible Zynq Shield
PCB Rev 1 are working and usable but there is room for BOM cost optimization. Current sale price could be 89 EUR, with extensive BOM optimization it could be lowered - hopefully. USB micro-B to USB mini changeFTDI USB connector is currently micro-B footprint...

Programming
Instructions from PiTagErrUs
The Arduino Micro Pro doesn't like to play with [Ken Shirriff]'s infrared library. [Link]Follow the instructions for installing this library. Once the library is installed, it must be modified to work our hardware. This troubled me and I followed forums...

Assembly
Log from GNSS module 2.0 - GNSS via Bluetooth
The build of the module was pretty strait forward...with some complications. Except for one all footprints matched the parts I have. The LDO for VCC_USB was the wrong footprint, a SOT-89-3 should have been a SOT-223. I fixed this by soldering cables...

Sun Tracker 2 Revision 1 - Prototyping Board
Log from SunTracker 2 Revision 3
With the compass functionality tested on a breadboard, the next step is to transfer it to a universal prototyping board, adding a status display and IO expansion ports to drive a LED ring that simulates the horizon. For the board, I am going to use the...

More Power Igor
Log from Cardware
Well, finally I was let down by a lack of amps, the batteries I have just arent strong enough to move the limbs without at least doubling them. And I'll need to upgrade the regulators. Such is life...I added a little bit of code to the Pi's monitor....

Lichee Zero u-boot Getting Started!
Project by NYH-workshop
What to do with a little SoC and an SD-card? Let's start with a little bit of u-boot!
- 2
- 1

SDR LimeToGo
Project by Djani
Remote RX SDR set built to be left outside for radio signal monitoring
- 9
- 8

DIY hobby servos quadruped robot
Project by Miguel Ayuso Parrilla
Cheap 3D printed 4 legged robot, that almost looks like boston dynamics spot but moves like a newborn.
- 2.8k
- 596

Le-Sk8te - Foldable electric longboard
Project by Lucas
Electric foldable longboard for micro-mobility and commuting
- 8
- 6

Scrumpel 7d Z8S180 SBC
Project by Nick Brok
The successor of Scrumpel 7c on one Eurocard PCB
- 11
- 9

WiFi Waterbed and Freezer Temperature Control
Project by nodemcu12ecanada
The old mechanical thermostat failed ON so I replaced it with a WiFi NodeMCU system with web page HMI for control/monitoring.
- 3
- 4

Easythreed Nano printer optimisation
Project by RobG
Squeezing maximum performance out of a cheap 3D printer
- 9
- 10

Calorie Restricted Phone Charging
Project by bornach
Stop overcharging your phone battery overnight. This puts your lipo batteries on a strict diet by limiting the mAh passing over a USB cable
- 5
- 5

1
2
3
4
5
>
>|