27106 Results for "《 예약문의 OIO↗8489↗8306》가라오케┦가라오케world선릉가라오케가라오케사이즈청담가라오케promotion 선릉가라오케┫ ∫선릉가라오케decided"

End Cap Assembly
Instructions from 2600 Magazine Storage System
As mentioned in the description, I put a window in each end cap as it saved approximately an hour of print time per cap. To fill in the void, I hand-cut pieces of 1 mm acrylic and glued them into place. Because of the way the cap is designed, the...

Introduction
Instructions from LoRa GPS Tracker Tutorial | LoRaWAN with Dragino
Hey, what's up, Guys! Akarsh here from CETech. A couple of projects back we had a look at the LoRaWAN Gateway from Dragino. We connected different nodes to the Gateway and transmitted data from the nodes to the Gateway using TheThingsNetwork as the server....

Get PCBs for Your Projects Manufactured
Instructions from LoRa GPS Tracker Tutorial | LoRaWAN with Dragino
PCBGOGO, established in 2015, offers turnkey PCB assembly services, including PCB manufacturing, PCB assembly, components sourcing, functional testing, and IC programming. Its manufacturing bases are equipped with the most advanced production equipment....

About LPS8 Dragino Gateway
Instructions from LoRa GPS Tracker Tutorial | LoRaWAN with Dragino
The LPS8 is an open-source Indoor LoRaWAN Gateway. Unlike the LG01-P single channel gateway. The LPS8 is an 8 channel gateway which means that we can connect more nodes to it and can easily handle comparatively larger LoRa traffic. The LPS8 Gateway...

About LGT92 LoRaWAN GPS Tracker
Instructions from LoRa GPS Tracker Tutorial | LoRaWAN with Dragino
The Dragino LoRaWAN GPS Tracker LGT-92 is an open-source GPS tracker based on Ultra Low Power STM32L072 MCU and SX1276/1278 LoRa Module. LGT-92 includes a low power GPS module L76-L and a 9-axis accelerometer for motion and altitude detection. The power...

Setting up the Node: Arduino based GPS tracker node
Instructions from LoRa GPS Tracker Tutorial | LoRaWAN with Dragino
In this step, we are going to set up the first type of GPS tracker node that we are going to connect to our Dragino Gateway i.e. The Arduino-based GPS node that we got with the Dragino Kit. This node has an onboard GPS Chip. Though we can also connect...

Programming the Arduino based GPS Node
Instructions from LoRa GPS Tracker Tutorial | LoRaWAN with Dragino
In this step, we are going to upload the program in our Arduino based node. For that, you need to refer to the GitHub repository for this project from here and follow the steps given below: 1. Head over to the Github repository. There you will see a...

Setting up the LGT-92 GPS Tracker node
Instructions from LoRa GPS Tracker Tutorial | LoRaWAN with Dragino
Till now, we have done the setup and configuration of the Arduino GPS node and sent data through it to the gateway as well. But as you can see that the Arduino Node is a bit bulky and not very much presentable. But not to worry as we have the LGT-92...

Testing the Working of LGT-92
Instructions from LoRa GPS Tracker Tutorial | LoRaWAN with Dragino
Till the previous step, we were done with the setting up, configuration part, and device registration of our LGT-92 GPS Tracker node. Now when we turn ON the LGT-92 we will see a green light while it turns ON. As the device will turn ON, the light will...

SAMD21 + QUECTEL L80 GPS
Instructions from Atomic Synchronator => TicTacSync
For now, I'm building TicTacSyncs with off the shelf boards, here an Adafruit Ultimate GPS FeatherWing (25 USD) and a Adafruit Feather M0 Basic Proto (20 USD): Flash the board using the Arduino IDE with this program: ppssyncYears.ino A motivated maker...

Flash the Sonoff Mini with Tasmota
Instructions from Sonoff Mini dual switch support
The Sonoff mini has a "DIY mode", which is for you, if you prefer learning a new rather complex proprietary process instead of wasting two seconds to pop open the case and another 45 to align a prommer to the flashing pads and flashing the normal way....

Add the new terminal
Instructions from Sonoff Mini dual switch support
Detach AC wires, pry open the device with a screwdriver/club card/, find the screw terminal blocks. In V2 the switch terminals are gray, in V1 black, find the ones marked S_IN and S_OUT = the ones with no thick solder snakes coming from them. Those...

Configuring Tasmota
Instructions from Sonoff Mini dual switch support
Now that we have the dirty stuff done, lets make Tasmota know about it. Open browser at the device's IP address, you should see the Tasmota main page. First click "Console" and there type "SerialLog 0", that will free the serial lines to us: Navigate...

Adding an external relay for the second circuit (optional)
Instructions from Sonoff Mini dual switch support
If you happen to need another relay (or an electrical output for something else) for the new switch instead of just sending state changes over MQTT, you sure can, it's your device. To make it more convenient and reliable, we chose the GPIO1 with its...

HOW TO FLASH M5StickC
Instructions from OXOTP
DOWNLOAD Flash Download ToolDOWNLOAD Last Release HEREOpen Flash Download Tool Restart your M5StickC after the flash is finished and enjoy it

|<
<
1274
1275
1276
1277
1278
>
>|