2337 Results for "B 남양주슬롯머신 cddc7닷컴 ♠보너스코드 b77♠카지노24🙍FC 에르츠게비르게 아우에ṅ수원장안 원엑스벳ే알제리Ẽ남양주슬롯머신좋은글 forasmuch/"

DIY Monitor ScreenBar WiFi RGB LED
Details from DIY Monitor ScreenBar WiFi RGB LED
The Monitor ScreenBar Wi-Fi RGB LED Light brings forth a revolution when it comes to interactivity with lights are concerned for Desktop Setup. This Monitor ScreenBar Wi-Fi RGB LED Light is Wi-Fi enabled thus making it wirelessly...

Digital Bicycle Horn With Customizable Sound
Details from Digital Bicycle Horn With Customizable Sound
in this project, we are going to make a digital bicycle horn with customizable sounds, we can produce up to 4 different sounds, and each track is saved on a micro-SD card in .mp3/wav format, we have 4 button inputs for playing sounds, each button is...

Lora Data Sender
Details from Lora Data Sender
The DHT22 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). It's fairly simple...

LM741 IC operational amplifier, Utsource
Details from LM741 IC operational amplifier, Utsource
Description LM741 IC is an operational amplifier, this IC is available in different package with single op-amp and others with more than one operational amplifier. LM741 IC has one operational amplifier inside. It is a DC-coupled high gain electronic...

Pebl - the complete IoT package for makers
Details from Pebl - the complete IoT package for makers
During our time away, we've been busy. We were being asked left, right and center if we'd be offering the Pebl for sale on our website despite not meeting our goal. Unfortunately, the answer was no as we just couldn't afford to do so :( However,...

Connect-PI
Details from Connect-PI
What is Connect-PI?Connect-Pi is an automation system with a responsive web app that is accessible on all smart phone, tablet and desktop devices. It is designed for your all automation projects and prototypes. Connect-PI consists of the following two...

IOT- SIM808 GPS Tracker Based on Arduino
Details from IOT- SIM808 GPS Tracker Based on Arduino
Integrated the power management and storage, this GPS tracker can be a solution for some IoT projects. absolutely open with eagle design files can modify the files as you like for your own projects. There is also another version with Arduino Zero. (ATSAMD21G18...

Cisco HWIC/EHWIC/VWIC Breakout Board
Details from Cisco HWIC/EHWIC/VWIC Breakout Board
The table shows some of the Cisco WAN modules and their main characteristics, such as FRGA type, memory chip, etc: HWIC-2SHDSLEHWIC-3G-HSPA+7-AVWIC3-2MFT-T1/E1EHWIC-4ESGHWIC-3G-CDMAHWIC-1ADSL1FPGA Cyclone II (EP2C35F484C8)Cyclone III(EP3C40F324C6N)Stratix...

7 Segment Led Clock
Details from 7 Segment Led Clock
The clock is made using arduino and other components as mentioned the files and all pictures are attached below the control of the clock is done by arduino or you can use 74HC595 Drivers for easy control In this case, I used it to simulate an analog...

ESP12.OLED - universal ESP8266+0.96"OLED MCU board
Details from ESP12.OLED - universal ESP8266+0.96"OLED MCU board
The development board has: PCB holes for GPIO pin-headers with step 2.54 mmESP8266-12 MCUonboard SSD1306 128x64 monochrome 0.96" OLED I2C displayFlash buttonRst buttonRGB LEDUART interface connection for testing and programming via terminal console....

LOKI 4G (Locate Observe Krack Isolate) 4th Gen
Details from LOKI 4G (Locate Observe Krack Isolate) 4th Gen
LOKI3D printed Airframe and basic hardware:Spyda DJI Arm compatible 3mm Solid Slotted Body Plates (2) http://www.thingiverse.com/thing:160607Spyda DJI bodyhttp://www.thingiverse.com/thing:230558Spyda Custom DJI arms with integrated landing gear holder.Custom...

CFexpress Type B to SSD Adapter Converter
Details from CFexpress Type B to SSD Adapter Converter
Simple Steps to install a 2230 NVMe SSD.

Digivibe
Details from Digivibe
Trello board (This is where I'll list project stories and progress)

Magnetic Pendulum
Details from Magnetic Pendulum
Quick Tour Video: Operation phase 1: Operation phase 2: Operation phase 3: Circuit Diagram: Circuit operation details: Magnet / Electromagnet / Hall sensor: IMPORTANT: 1) electromagnet north pole pointing UP 2) pendulum north pole pointing DOWN...

Wi-Fi Controlled Robot Using Blynk App
Details from Wi-Fi Controlled Robot Using Blynk App
There are several ways to use this tutorial. You can use it to: - Learn how to program an ESP8266 using the Arduino IDE; - Practice your electronics and soldering skills, etc; - See how to assemble a robotic kit; - Learn how to use Blynk app on your...

|<
<
4
5
6
7
8
>
>|