16 Results for "bldc"

Body Wand Hack
Instructions from Body Wand Hack
Wire the BLDC up to the ESC and the EXC to the arduino

Body Wand Hack
Instructions from Body Wand Hack
Grind a flat/key on the shaft of the BLDC motor to slip in to the vibrator connector.

Body Wand Hack
Instructions from Body Wand Hack
Machine up a holder that allows the BLDC motor to fit in where the old motor came from

build physical object
Instructions from Aruna - ROV
print necessary parts: (get them from https://github.com/aruna-rov/ROV-CAD-objects) 6x BLDC 4x 45_deg_mount 3x universeel_houder 1x dop Four times: mount BLDC and 45_deg_mount together with the BLDC facing up and the 45_deg_mount making a 45 degree...

Necessary parts
Instructions from Aruna - ROV
ESP-32D (S should also work but why bother) RS485→ UART breakdown board (for communication from ESP to computer) RS485→USB (for communication from computer to ESP) 10 meter long cable with 2 wires for RS485 (Ethernet cable works fine) 3D printer w/...

Gimbal
Instructions from Augmented Mekamon Robot
The gimbal is an implementation of the open source project STorM32bgc http://www.olliw.eu/2013/storm32bgc/ using a generic v1.32 board from Gearbest, and £10 gimbal BLDC motors from Hobbywing. Here is the reference for the STorM32 Remote Control...

3D-Printed Electric Longboard
Instructions from 3D-Printed Electric Longboard
Step 7: Electronic ComponentsWe are now done with the mechanical set up of our longboard. Next, we need to wire up the VESC to the batteries and receiver. It is a very straight forward procedure. Before we start, make sure all connectors are compatible....

Know the Components
Instructions from DIY Arduino based Quadcopter Drone
Before moving on to the Assembly part, you first need to know the components that we are going to use to better understand what you are doing. So, let's discuss the components one by one:- DJI F450 Frame: The frame that we have used is one of the best...

Purchase your fans
Instructions from PC 140mm Air Filter
Head out to DigiKey and find some fans you like. Here is a query to get you started. 12V4-pinTube axialStatic Pressure at or above 0.5 inches of H20Sizes (square) 70mm80mm92mm92.5mm119mm120mm NOTE: The GitHub repository only includes OpenSCAD...

Electronics/Finishing - Step 3
Instructions from MiniHawk VTOL
Solder the BLDC Motor leads to each respective ESC, or use bullet-connectors or otherwise as desired. Solder the ESC power connections directly to the Flight Controller's Power-Distribution region, or to intermediate connections as desired. Power on...

Introduction
Instructions from DIY Arduino based Quadcopter Drone
Hey, what's up, Guys! Akarsh here from CETech. This is the third and final part of our Arduino-based Drone Series. In the first part, we made a flight controller for our drone using the Arduino Nano and MPU6050 module. In the second part, we made an...

Groundstation
Instructions from Kites for Future - Flying Wind Turbine
The groundstations main part is an electric motor (used as a motor and of course as a generator). We have chosen a very commonly available 3-phase BLDC brushless motor. It has a stator with 3 phases and a rotor with alternating permanent magnets. Attached...

3D-Printed Electric Longboard
Instructions from 3D-Printed Electric Longboard
Step 3: Motor MountSo, this is basically the most tedius part of the build if you are looking to design a motor mount out of ABS that can withstand large braking forces. The files can be found on my Thingiverse. It has been designed in such a way that...

Assembling the Frame of the Drone
Instructions from DIY Arduino based Quadcopter Drone
In this step, the assembly of the drone's frame will be done. Along with the frame, motor placement and their connection with ESC will be completed. So you need to follow the instructions given below to get the frame ready:- In the frame accessories,...

Calibrating the Electronic Speed Controllers
Instructions from DIY Arduino based Quadcopter Drone
In this step, you need to calibrate the ESCs. By calibrating here we mean to say that we are going to inform our ESC of the max and min limit between which it is going to be operated. The Calibration of ESCs is necessary to prevent some problems such...

1
2
>
>|