Close

6880 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄ 『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

  • MCM/70 Reproduction
  • Details     from MCM/70 Reproduction
  • Inspiration I've been a vintage/retro computer enthusiast for a long time now and thought that I had a pretty good handle on all of the machines available in the 60s and 70s. So imagine my surprise when I saw the Kristina Panos February 23, 2022 blog...

  • "Chad" - The NFC Voting System
  • Details     from "Chad" - The NFC Voting System
  • The OriginsWhen we decided to throw a party in LA (which became know as The Gathering) I wanted it to be more than just free t-shirts and beer. Laser Graffiti popped to mind and I was glad that Ben was willing to take the lead on that project....

  • Arduino-Compatible FPGA Shield
  • Details     from Arduino-Compatible FPGA Shield
  • Intending to keep this as compact as possible I'm looking at BGA packages for SRAM and std package for the SPI Flash.  The several that I've chosen will enable me to keep costs below $30 for the whole board (target = $25) and still have head room...

  • X12 Turtle Beach Headset Hack
  • Details     from X12 Turtle Beach Headset Hack
  • I needed to remove the dials and the switch from the board because I wanted to have them accessible from the rim of the ear muff. However, each of these components had a minimum of 5 pins. My approach was to use a hot air gun to melt all the solder on...

  • X12 Turtle Beach Headset Hack
  • Details     from X12 Turtle Beach Headset Hack
  • I needed to remove the dials and the switch from the board because I wanted to have them accessible from the rim of the ear muff. However, each of these components had a minimum of 5 pins. My approach was to use a hot air gun to melt all the solder on...

  • DIY SlingBox $30
  • Details     from DIY SlingBox $30
  • The transmitter in the fourth picture uses a few more parts. I had a 3.3V breakout board and the signal reached only about a yard. So I added a 555 voltage doubler to Albert's hardwarehttp://www.talkingelectronics.com/projects/50%20-%20555%20Circuits/50%20-%20555%20Circuits.htm...

  • Pinewood Derby Police Car
  • Details     from Pinewood Derby Police Car
  • So my son, [B]  did the soldering work. His uncle help him mill out the inside of the car to fit the electronics. [B] Drilled the holes for the lights and then painted the car with little sisters help.  We tested the code on the MSP430 launch...

  • Astrarium
  • Details     from Astrarium
  • There's an old hard-disk which I stripped down so that the front only has spindle coming through. I used a mill to face off some of the protuberances and other features which held the read/write head-arm in place.  At the bottom there is a PCB I...

  • Il D'oro Bass Guitar Amplifier
  • Details     from Il D'oro Bass Guitar Amplifier
  • I've wanted to build my own amp for quite a while. For bass guitar, the selection of amplifiers you can buy is pretty lack-luster, and mid-volume studio amps are hard to find. It seems like most of what's available is either a practice amp or a stadium...

  • reflow
  • Details     from reflow
  • Currently this bad boy has two modes: hit and hold. Hit turns on the heat until the set temperature is hit, then shuts off. Hold tries to hold the temperature at the setpoint.It also has a FTDI USB to UART IC, so it can be loaded with optiboot (after...

  • HydraBus v1 Rev1.5
  • Details     from HydraBus v1 Rev1.5
  • HydraBus v1.0 Rev1.5 In Stock on DigiKey:https://www.digikey.com/en/products/detail/benjamin-vernoux/hydrabus-v1/15652912 Features of the HydraBus board: Very small board only 60mm x 37mm size (extensible with shield which can be connected on top or...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday