Close

480 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄ 『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

  • Hummingbird
  • Instructions     from Hummingbird
  • Step 3: Connect to VivaPlanetThis next step is a bit more complex and requires some C# and visual studio with the Gagetter software from GHI Installed. This will take some time...persist it will be worth it in the end...There are a lot of great tutorials...

  • Wearable computer
  • Instructions     from Wearable computer
  • On the raspberry pi, you may need to affix the battery pack to the pi. I recommend a rubber belt (of the variety used in small vacuum cleaners); however, several rubber bands will do.I recommend taking some foam and cutting a rectangular hole slightly...

  • Awesome Jacket
  • Instructions     from Awesome Jacket
  • The Arduino was programmed to cycle through the sound files on the SD card mounted on the SOMO-14D. Each time a file is selected, a pulse was sent to the EL sequencer to coordinate the "light show effect". The Arduino also monitored the switch cct status...

  • Futurama's Jack dispenser
  • Instructions     from Futurama's Jack dispenser
  • Go to the Raspberry Download Page and download N.O.O.B.S. Follow the documentation to install N.O.O.B.S on your SD Card. When it's done plug it into your Raspberry Pi, power it up and choose your Operating System to install.For the rest of the instructions,...

  • ZRTP Hardphone
  • Instructions     from ZRTP Hardphone
  • ### [ WRITE IMAGE TO SD ]wget "http://93.174.101.10/bt/09bc05ab03780f279390e9cf6a15c7c249f712e1/data/2014-01-07-wheezy-raspbian.zip"7z x 2014-01-07-wheezy-raspbian.zipSD_CARD=/dev/sdX # Change it to your SD card device namemd5sum 2014-01-07-wheezy-raspbian.img...

  • Lexitron RSS Reader
  • Instructions     from Lexitron RSS Reader
  • Warning: hacker construction projectIf you are interested in making something like this, be warned. This project is a total hack job and will not run on any out-of-the-box hardware I am aware of. Development boards are available, but would require modification...

  • Lexitron RSS Reader
  • Instructions     from Lexitron RSS Reader
  • Tickernut circuit design and hardware:Enclosure:The motherboard is shaped to fit tightly inside a standard ABS jiffy box which set its limited size. The box has cutouts to expose all motherboard connectors on the left side and a small speaker and antenna...

  • Lexitron RSS Reader
  • Instructions     from Lexitron RSS Reader
  • Tickernut firmware:Ethernut is an Open Source Hardware and Software Project for building tiny Embedded Ethernet Devices. It consists of a set of hardware designs all running an open source operating system called Nut/OS and a TCP/IP protocol suite named...

  • Lexitron RSS Reader
  • Instructions     from Lexitron RSS Reader
  • Tickernut construction log:Construction was completed in stages over the period of many months with a design that evolved to suit the available parts.  The progression of construction was arranged so that each stage could be completed and tested...

  • Smart Cap
  • Instructions     from Smart Cap
  • Step 5: Setting up the voice recognition software for your DIY head mounted display Different screenshots from the head mounted displayI have prepared an interactive voice response system that responds to certain voice commands and gives you appropriate...

  • aquaPionics
  • Instructions     from aquaPionics
  • Assemble a base-station from a Raspberry Pi B+, sd-card, power supply and rfm12b dongle. You can use a JeeLink or a directly connected board.

  • aquaPionics
  • Instructions     from aquaPionics
  • Download the thingbox.io image to the sd-card and boot the Pi. If you're using a direct connection you'll have to enable SPI and install the drivers - instructions here.
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday