3995 Results for "『 모든문의 OIO=5793=7458 』 선릉셔츠룸㈄『 모든문의 OIO=5793=7458 』 Ηcake²셔츠룸테란강남셔츠룸デwriter 셔츠룸테란강남셔츠룸 선릉셔츠룸⒁셔츠룸사이즈┲exhausted⅔"

Setting up Ameba to be I2C Master
Instructions from Communicate with Arduino UNO via I2C
Next, open another window of Arduino IDE, make sure to choose your Ameba development board in the IDE: “Tools” -> “Board”Then open the “Master Writer” example in “File” -> “Examples”...

Setting up Arduino Uno to be I2C Slave
Instructions from Communicate with Arduino UNO via I2C
In this example, we use Ameba as the I2C master writer, and use Arduino as the I2C slave receiver.When the I2C slave receives string sent from I2C master, it prints the received string. Setting up Arduino Uno to be I2C Slave First, select Arduino in...

All of the steps for the project!
Instructions from Air Pollution Monitoring Project
Let’s get to it! Install Arduino IDE, the esp32 board and the Fixed Libraries. To install the ESP32 board in your Arduino IDE, follow these next instructions: 1) Open the preferences window from the Arduino IDE. Go to File> Preferences 2) Enter https://dl.espressif.com/dl/package_esp32_index.json into...

Arduino-Compatible FPGA Shield
Instructions from Arduino-Compatible FPGA Shield
Step 2 - Import the Arduino board file into Altium Designer: Using Altium Designer (AD) requires that I import Eagle board into AD. AD14.x includes an Eagle importer. Used source files from the Arduino site to import in AD.

Arduino-Compatible FPGA Shield
Instructions from Arduino-Compatible FPGA Shield
Step 3 - Build major footprints: Costing the available board area requires building the major footprints and placing them on the PCB. Built early footprints and placed to determine what additional space is avail. Files in git.

TI-84+ SE Backlight
Instructions from TI-84+ SE Backlight
Unscrew the circuit board and pull off the RF shield. Be carefull because once you take the board out there will be nothing holding the buttons in.

TI-84+ SE Backlight
Instructions from TI-84+ SE Backlight
Carefully bend the EL panel leads so they fold around the back of the PCB. The panel can bend pretty far, just don't crease it.Now install the board back in the front half of the case and screw it down. The EL panel leads will stick up through gap between...

HP Touchpad Charging Wall Mount
Instructions from HP Touchpad Charging Wall Mount
If you walls are textured, you'll need to texture the wall to match. If you have a special texture (other than spray like mine) you might practice on a scrap board as you want this to match seamlessly.

Wearable computer
Instructions from Wearable computer
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

Wearable computer
Instructions from Wearable computer
The board with the USB-like connector on it will be connected to the colored wires via surface-mount solder on top of vias. This is a really bad thing for the kind of torque you are likely to put on this connector board. So, desolder these wires using...

Wearable computer
Instructions from Wearable computer
Unscrew one of the threaded caps on the goggles and remove the clear plastic pane. (Your pair may have a silvered or coloured glass pane on top; if so, remove this as well but do not drill into it -- discard it or keep it as backup for the other side.)In...

Wearable computer
Instructions from Wearable computer
On the board containing the USB-like connector, on the edge opposite the connector whose wires you have resoldered, fold a piece of velcro. Connect the connector and then position a piece of velcro of the opposite type on top of your mask based on where...

Wearable computer
Instructions from Wearable computer
Disassemble the primary unit of the video glasses, which now resembles a black plastic bar. You should end up with two boards connected by a thin-film ribbon cable, one of which is connected to another board (containing a USB-like plug) connected by...

Solid-state garduino with RTC & LCD!
Instructions from Solid-state garduino with RTC & LCD!
(These are the areas I wing it.)Get a board slightly larger than the footprint of your fluorescent lamp.Layout your junction boxes approximately how you'd like them to sit.

CUBEX
Instructions from CUBEX
Download and build board files: https://github.com/arkorobotics/CUBEX_V1/tree/master/Board

1
2
3
4
5
>
>|