Close

1545 Results for "《〈 문의 OIO↗5793↗7458 》〉 강남셔츠룸ㅬ レresidence㎱강남셔츠룸신사셔츠룸⑧appetite 강남셔츠룸강남란제리 강남셔츠룸╃강남란제리″names㏊"

  • The Dune Pain Box
  • Instructions     from The Dune Pain Box
  • To get a good idea how we made the electrodes, you can read the project update entitled "The Hand Thingie".  If you want to use the same sensing set up we used, this worked well.  Any sort of Object that is fairly ergonomic and can have the...

  • Jewel Box Servo Meter
  • Instructions     from Jewel Box Servo Meter
  • Find a small wooden box with a lid that has a transparent panel in the lid. My box had a thin wooden panel so I had to carefully cut out one end to remove the panel. Remove all the hardware. Stain and finish the box. Cut a piece of plastic from a CD...

  • Jewel Box Servo Meter
  • Instructions     from Jewel Box Servo Meter
  • Test fit all the components in the box to find the best arrangement. Cut a piece of strip board 8 rows wide and up to about 25mm long that will fit flat on the floor of the box. The strip board will act as a bus to connect to the header. I placed the...

  • Jewel Box Servo Meter
  • Instructions     from Jewel Box Servo Meter
  • Bend the pins on the header at a right angle. Drill 8 holes 1/16-inch (1.6mm) diameter in a line spaced 0.1-inch (2.54mm) on centers. Pass the pins through the holes with the header on the underside of the box.

  • Jewel Box Servo Meter
  • Instructions     from Jewel Box Servo Meter
  • Fasten the servo to the inside of the box with double sided tape. Measure the distance from the center of the drive gear to the box. Place little blocks in each corner of the box at the same level of the top of the servo hub. These will serve to hold...

  • Jewel Box Servo Meter
  • Instructions     from Jewel Box Servo Meter
  • Layout a meter dial using free MeterBasic software from www.tonnesoftware.com. Print the dial on glossy photo paper. Cut a slot for the servo gear drive and place the dial in the box. Make a pointer from a tie-wrap. Cut or file the hub to the same thickness....

  • Jewel Box Servo Meter
  • Instructions     from Jewel Box Servo Meter
  • Temporarily put a jumper between ground and the input pin on the header under the box. Turn on the system. After a 5 second delay the servo should move to zero then full scale then back to zero.  You may have to adjust the mounting of the pointer...

  • Portable LED Floodlight
  • Instructions     from Portable LED Floodlight
  • Get yourself a box, and you put that stuff in the box.What I ended up doing here is mounting metal supports to the metal tripod pole. I then used lacing twine and laced the battery to those supports, the plastic bin is basically just sandwiched in there....

  • IRK! Infrared Remote USB Keyboard
  • Instructions     from IRK! Infrared Remote USB Keyboard
  • Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

  • Trombino
  • Instructions     from Trombino
  • Drill two holes in the lower half of theArduino box and fix it to the top of the potentiometer housing. Thread wires through the holes. Add in the Arduino, ethernet shield and breadboard and hook up the parts currently attached to the housing. Open up...

  • Trombino
  • Instructions     from Trombino
  • Solder on the parts for the second part of the strip board and affix it in the lid of the box.

  • Trombino
  • Instructions     from Trombino
  • Place the lid close to the bottom and wire everything in, trying to keep the wires short. There is very little clearance at the top of the case so anything attaching to the shield should not have extra height (eg no jumper cables!). After everything...

  • Low Cost CO2 Laser Build
  • Instructions     from Low Cost CO2 Laser Build
  • NaCl Window0NaCl Window and and Mirror – DIY OCWell, I decided to give this a try for the OC of the CO2 laser. A simple gold mirror with a hole in the middle and a salt window. The hole was easy, I simply put a glass drill bit into a battery powered...

  • DIY Variac
  • Instructions     from DIY Variac
  • After some looking around I got this one for 30 dollars.It was bare, but that is ok. I looked around for a container for it, and could not find one that I liked. I considered building one out of wood, but chose against that as well. One option was to...
Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2024 Hackaday