13109 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 쓰리아워⒬ 쓰리아워pillowШ쓰리아워가격강남술집정보쓰리아워가격mild 강남쓰리아워∂강남술집정보∵㎃쓰리아워poor"

Make and Feel Virtual Drawings
Instructions from Make and Feel Virtual Drawings
Hack a mouse (optional) Open the casing of the mouse, and remove the scroll roller.Now, you should have space to place the servo motor like in the picture.To paste servo motor on the mouse board, use a glue gun or double sided tape.Now, there should...

Quick and Nasty Tube Power Supply
Instructions from Quick and Nasty Tube Power Supply
Now you can slip the remaining I laminations into the gaps left by the E laminations. Leaving the last few E's out will make it easier to do this. You can then complete it by sliding in the remaining E pieces, then the I's. It should be a snug fit.

Quick and Nasty Tube Power Supply
Instructions from Quick and Nasty Tube Power Supply
Now you can start to remove the E and I laminations one by one. Just run a knife between each lamination and it'll break off. Be sure to put them in a container of some sort instead of just piling them up on the table (as pictured).

Quick and Nasty Tube Power Supply
Instructions from Quick and Nasty Tube Power Supply
You should be left with a stack of iron sheets and a core.Assuming you've bought the right type of transformer, the core should be made up of two bobbins which can be pulled apart.Keep the thick cardboard that surrounds the bobbins!

Quick and Nasty Tube Power Supply
Instructions from Quick and Nasty Tube Power Supply
Take the two 240V bobbins and put them together with the protective cardboard and anything else that looks important. Now it's time to reassemble all that iron!(In this example, I wound a filament winding on top of the second 240V winding. I don't actually...

Quick and Nasty Tube Power Supply
Instructions from Quick and Nasty Tube Power Supply
I start with these transformers by layering up the E's in alternating order. That is, put one in from one side, then the next on the other, and so on. Leave the last one or two out.

Shootable ALIENS Egg & Jumping Facehugger Target
Instructions from Shootable ALIENS Egg & Jumping Facehugger Target
Use laser cutter to cut out a Facehugger pattern and a paint stencil.You can download the DXF file from the links section (left side of main project page.) Use only the outline to cut out Facehuggers. Use all the inside holes to make a paint...

Shootable ALIENS Egg & Jumping Facehugger Target
Instructions from Shootable ALIENS Egg & Jumping Facehugger Target
Cut out a few Facehuggers and paint each one via the paint stencil.

Shootable ALIENS Egg & Jumping Facehugger Target
Instructions from Shootable ALIENS Egg & Jumping Facehugger Target
Glue a clay pigeon to the back of each Facehugger.

Shootable ALIENS Egg & Jumping Facehugger Target
Instructions from Shootable ALIENS Egg & Jumping Facehugger Target
Now make the Egg. I used Google image search to find a half-decent picture of an egg and had it printed in color at a print shop.Glue it to some sturdy cardboard and then cut it out.

Shootable ALIENS Egg & Jumping Facehugger Target
Instructions from Shootable ALIENS Egg & Jumping Facehugger Target
Attach the Egg to the front of the popper. I used some caulking, but any sturdy, gap-filling glue should do the trick.

Shootable ALIENS Egg & Jumping Facehugger Target
Instructions from Shootable ALIENS Egg & Jumping Facehugger Target
Attach the pigeon flipper attachment to the popper. The popper is a heavy steel plate that falls when shot.That plate hits a lever, upon which is a clay pigeon. It acts like a catapult and tosses it into the air.The Facehugger goes where...

Shootable ALIENS Egg & Jumping Facehugger Target
Instructions from Shootable ALIENS Egg & Jumping Facehugger Target
Set it up in a suitable place, load up your shotgun, and so some live-fire ALIENS re-enacting!

Experiment Bioroid!
Instructions from Experiment Bioroid!
By using "Dremel circle cutter" cut two plastic circles177mm Diameter for pressure sensitive surface155mm Diameter for bottom baseIn my case I build my own circle cuttercheck video for details https://www.youtube.com/watch?v=D8kZFAhsS1g

Experiment Bioroid!
Instructions from Experiment Bioroid!
Wheels to servo connectionsandpaper wheelSuper Glue each wheel to servo horn (included with each HS-322HD servo)use center tool(m3 bolt with tape/spacer) to align horn on center.

|<
<
5
6
7
8
9
>
>|