324 Results for "《〈 문의 OIO↗5793↗7458 》〉 강남셔츠룸ㅬ レresidence㎱강남셔츠룸신사셔츠룸⑧appetite 강남셔츠룸강남란제리 강남셔츠룸╃강남란제리″names㏊"

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
Now that most of the holes (drill/cutouts) have been made in the enclosure, it’s time to start installing stuff in there. First, take 4 ¾” 4-40 screws (preferably nylon), and insert them through the holes drilled for the Arduino.They’ll want...

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
Next, the reset switch. Grab one of the two red pushbutton switches, solder wires to both terminals, put on heat shrink insulation over the exposed leads if necessary, then install it in the small hole in the upper left corner of the left side. Connect...

Affordable Reflectance Transformation Imaging Dome
Instructions from Affordable Reflectance Transformation Imaging Dome
The previous stand instructions let you build a simple stand that will work for basic functions, and is satisfactory for larger domes. However, for small domes (12”-15” in diameter), I’ve come up with an alternate design that can be used...

K8200 3DRAG retrofit
Instructions from K8200 3DRAG retrofit
Use 8 M4x20 bolts and nuts with a locking washer to connect each side of the frame.For the motor mount make two assemblies as displayed, from two M5x40 bolts, three diameter 10mm M5 washers and 2 diameter 20mm washers and a 525 bearing.Then connect the...

K8200 3DRAG retrofit
Instructions from K8200 3DRAG retrofit
Build four assemblies as shown above. With a M5x40 bolt, a 20mm washer, a 10mm one, the bearing, another 10mm washer, a locking ring, a nut and then another nut, two 20mm washers, a locking ring and a final nut. These will form the horizontal guides....

Making a Modular Differential Drive Robot
Instructions from Making a Modular Differential Drive Robot
First, we will mount motor clamps which is used to fix motors to the base plate. The plate have the mounts for two clamps. Mount the clamp with for nut bolts tightly.

Making a Modular Differential Drive Robot
Instructions from Making a Modular Differential Drive Robot
Mounting motors and wheels to base plateAfter you have mounted the clamps, then we will mount motors. Unscrew the nut from the motor, then insert the motor in the clamp and screw back the nut to fix the motor in the clamp.Then do the same thing for the...

LED Beer Pong Table
Instructions from LED Beer Pong Table
Drill a hole through the brace that is flush against the leg, through the leg. Repeat for all the legs. This is for the through bolt and wing nut to lock the leg in the upright position.

OpenChair
Instructions from OpenChair
Disassembly: wheelchairRemove the manual wheels from the wheelchair. Gripping the nut in the wheel axis, unscrew the axis and take off the wheels.

Adjustable Angle Knife Grinding Jig
Instructions from Adjustable Angle Knife Grinding Jig
These are the parts I bought for the project:Everbilt 4.5" adjustable spring hinge - 1xMetal angle bracket (sturdy) - 1x3/8" - 16 x 2" SS Socket Cap Screw - 1pk3/8" - 16 x 7/16" T-Nuts - 2pk1/4" - 20 x 1" Flat Head machine screws with nuts - 4pkM10 Cap...

Adjustable Angle Knife Grinding Jig
Instructions from Adjustable Angle Knife Grinding Jig
Next up was adding the mount for the 3/8" screw, which will adjust the angle. My first attempt at this was with some more of the 1/2" plastic, but I found that the unthreaded part of the screw hit the T-nut too soon, which limited the angle, so I switched...

Adjustable Angle Knife Grinding Jig
Instructions from Adjustable Angle Knife Grinding Jig
All that was left was the final assembly. Insert that last screw, add the cap nut (I stuck a tiny screw into the cap nut first so it wouldn't screw down all the way, giving me a bit more length), and setting up the spring inside the hinge. I was especially...

Arcade Stick with rubber bands
Instructions from Arcade Stick with rubber bands
Slightly adjust the threaded rod with a washer and nut from top and below the top baseHookup a rubber band between one threaded rod, below the top washer and one of the corner bolts.Then go to the opossite side and hookup another, and another till you...

GPS Clock
Instructions from GPS Clock
Place the board on the screws with the switches on the back sticking into the switch holes. Add a lock washer onto each bolt and then a nut. Before tightening each nut, double-check that the switch posts are correctly placed in the switch holes and not...

GPS Clock
Instructions from GPS Clock
Install a screw in each of the remaining holes on the back panel and loosely thread a nut onto each only a single turn. The nut goes on the inside and the bolt head on the outside.

|<
<
3
4
5
6
7
>
>|