39 Results for "%E3%80%8A%20%EC%98%88%EC%95%BD%EB%AC%B8%EC%9D%98%20OIO%E2%89%A1%E2%91%A7%E2%91%A389%E2%89%A183O%E2%91%A5%E3%80%8B%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%EA%B2%AC%EC%A0%81%E3%82%88%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8ago%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%83%A1%EA%B0%95%EB%82%A8%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8eighty%20%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%CE%BA%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%E2%92%B2%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%83%A1%EF%BD%83%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8literary"

Clone of stEve
Instructions from Clone of stEve
- A1,A2,B1,B2 assembly snaps into base C (line it up and pull the two spring clips back if necessary)- Tape a nut into slots on B1 & B2 (tape on one side should be enough to stop the nut falling out)

Think about a layout or box
Instructions from CarbOnBal
If you want to build this project I suggest you think about a box first. My prototype proves the electronics and software works. For the new prototype CarbOnBal Basic, I wanted a box, it looks better and is much easier to handle. My design (if...

Axis assembly
Instructions from LumiClock
Feed the leadscrew through the central horizontal hole and through the nut. Spin the arm down the thread about half way down. Take the motor support and rail support asembly and into one of the 4mm holes insert a 31mm threaded rod with 5mm of rod visible...

Lexitron RSS Reader
Instructions from Lexitron RSS Reader
Tickernut circuit design and hardware:Enclosure:The motherboard is shaped to fit tightly inside a standard ABS jiffy box which set its limited size. The box has cutouts to expose all motherboard connectors on the left side and a small speaker and antenna...

Code
Instructions from Create Your Own Apple AirTag
// You should get Auth Token in the Blynk App. // Go to the Project Settings (nut icon). char auth[] = "YourAuthToken"; // Your WiFi credentials. // Set password to "" for open networks. char ssid[] = "YourNetworkName"; char pass[] = "YourPassword";...

Materials and Tools
Instructions from PantoProbe
Things you'll need to build a PantoProbe: Materials: 4 x 0.2" lengths of 3/16" brass tubing4 x 0.69" lengths of 5/32" brass tubing8 #8 SAE flat washers 1 1/4-20 nut1 1 " long 1/4-20 bolt5 3D Printed...

J1772 Hydra
Instructions from J1772 Hydra
Prepare the internal mounting plate. You will drill holes to mount the two contactors, the power distribution bus, the ground bar and the standoffs for the boards. The plate can be divided logically into the top and bottom half along the center, which...

Tools and Skills Needed
Instructions from Ultraviolet Microwave (name subject to change)
Phillips screwdriver, #6 nut driver, portable drill with drill set, two step tab connector crimper (Molex 63811-1000 or equivalent), needle nose pliers, wire cutters and wire stripper, scissors, and masking tape. You may need the Tamperproof Torx. This...

Mount Ball Head Mounts
Instructions from Solar Mirror Array
Place a regular 1/4" 20 nut on all bolts sticking out of the frame and then add a lock washer above the nut. I spun the nut down as far as it would go with my fingers. Screw on all the Ball head mounts on top of the bolts. They will vary slightly in...

Ball Screw
Instructions from 3D Printed Ball Screw Actuator
Begin by dry fitting balls/nut with bearings. Fit should spin freely without bearing skidding. Assemble using lithum grease and use the retainer and belt pulley to retain the bearings setting the encoder gear towards the frame.Assemble Frame center onto...

Make the Mass Holder
Instructions from Seismometer
I used an empty tomato paste can to hold the lead weight of the mass. (A tomato sauce can is too wide.) shorten the can to be approximately 1.5" tall.drill a 1/4" hole in the center of the bottom of the can.push a 1.5" long 1/4 x 20 bolt into the...

Tray and mounts
Instructions from Racing Spider
Parts to Print1x Tray-full.stl (or A, B & C for 6" print bed)6x Bearing-rib.stl4x spring-mount.stl1x Mount-mount.stl Parts6x 10mm screw10x 10mm counter-sunk screws (+4 for 3 part tray)18x 3mm nyloc hex nuts ToolsScrew driverSoldering Iron Assembly...

Tripod Mount
Instructions from SASS-style Stereo Microphone for Nature Recording
The 3D Printed Tripod Mount with the 1/4-20 nut is pressed into the foam to indent it, marking where to cut out clearance for the mount. As shown in the picture above put a circle of duct tape over the nut so that glue does not seep into it. Now hollow...

Hinge assembly
Instructions from Zvychai One
Grab both M5 x 20 bolts, align alpha/omega hinge parts together, apply washers to the external side and put on the wing nut: You can do this also with the hinge already installed on both keyboard carrier and primary case, but if you did not - do it now....

Annotated CNC Assembly Sketch
Instructions from WEEDINATOR 2019
The sketch below shows the main parts for building the CNC mechanism. The whole set of drawings are bundled in 3 zip files. X axis is HERE, Y and Z axis's are HERE. Claw mechanism (R axis) is HERE. Parts: X axis saddle box section, 4mm x 100 x 200 x...

1
2
3
>
>|