1979 Results for "↘ 최저가 Ò1Ò〈⑻⑷89〉83Ò⑥ ↗ 강남쓰리아워Ｆグpossibility쓰리아워┃쓰리아워가격쓰리아워레깅스룸Ｉシ쓰리아워레깅스룸unnatural 쓰리아워ы쓰리아워레깅스룸㏅㈇temper"

Animatronic Iron Man MKIII suit
Instructions from Animatronic Iron Man MKIII suit
Notes about tools and materials used:ProPoxy 20 is awesome stuff. When making the brass tube pivots for the shoulder rocket pods it was easiest to glue the brass tube to the servo casing with superglue ( I use Gorilla glue with a spray accelerator) and...

Late Night Reading Lamp
Instructions from Late Night Reading Lamp
Solder LEDs, resistors etc onto a bit of veroboard. I used a female PCB header for plugging in the battery so that I didn't have to route long cables around the frame. Leave some length on the LED pins so that they stand up a bit from the veroboard

Tiny Ruler
Instructions from Tiny Ruler
Etch the pcb (maybe use black FR4 and silver plate the traces? would probably look very cool ;) )

Tiny Ruler
Instructions from Tiny Ruler
solder the components to the pcb starting with the smd components (there are very good how-tos on smd soldering)

ChipWhisperer®: Security Research
Instructions from ChipWhisperer®: Security Research
You can then decide to mount the parts in the OpenADC section, or build a separate OpenADC PCB. My examples always use a separate PCB, but the exact same circuitry is placed onto the PCB itself. See detailed build instructions on the OpenADC Wiki [link:...

IRK! Infrared Remote USB Keyboard
Instructions from IRK! Infrared Remote USB Keyboard
Through Hole Technology (THT) versionThis is how I built the Through Hole Technology version Make a double-sided fibre glass PCB (see front- and back- PDF files below). There are several ways to do this. The way I do it is to print the front and back...

Raptor12 Wireless AC Dimmer
Instructions from Raptor12 Wireless AC Dimmer
Axial Components:Were going to start with the polarized components theses only function in the correct orientation. The way to determine the way the go is simple, look for the band around the diode in theses case it is black. Match the band the the symbol...

Raptor12 Wireless AC Dimmer
Instructions from Raptor12 Wireless AC Dimmer
Q1 is a high voltage npn transistor, in this case its a mpsa42. Carefully bend the pins outword so they can fit into board. Push the component in until snug its fine if you can still see the pins of this transistor on the top side , idelay you dotn want...

Raptor12 Wireless AC Dimmer
Instructions from Raptor12 Wireless AC Dimmer
Green indicator leds D1 D2 (near fuse holder) D6 D7(at the top right.) Leds are polarized you need to get them the right way around, look at the symbol on the pcb it shows a circle with a flat side. Match that flat edge to the flat edge on the led.These...

Sugarcube - a tactile music controller
Instructions from Sugarcube - a tactile music controller
Solder LEDs and diodes to sparkfun board, be mindful of their orientation.Thread the leads of 16 LEDs (5mm or 3mm are fine, I used 5mm) through LED holes in the Sparkfun PCB. These boards are compatible with 4-lead RGB LEDs, so there are four available...

HPDL watch
Instructions from HPDL watch
Let's start with PCB. I wanted to mound display on one side of the PCB and the uc - on the other. Unfortunatelly, uc barely fits in the middle of the display's back and some pinout traces of display and uc touches where they mustn't. The traces...

HPDL watch
Instructions from HPDL watch
Add a battery holder and upload the firmware. I had a holder which was designed for thinner battery than CR2450. I wanted to bend it's top pin but I broke it, so I had to make it from wire. By the way, I had to extend the gap between it's pins...

HPDL watch
Instructions from HPDL watch
Make a whristlet:It is very easy. You can see holes on my manufactured PCB. I just mounted screws through them and bent 2 pieces of wire like in the foto which can be placed on those screws over cut off gaps of PCB. The whristband itself is made...

ATX power supply conversion for bench usage
Instructions from ATX power supply conversion for bench usage
Prepare the adapters and connect them to the terminal stripsThis part is important and tricky, and it took me three attempts to get this right. Here's the rules: Any high-current line must be a twin line that starts as a twin at the power supply's PCB...

Single Chip AVR BASIC Computer
Instructions from Single Chip AVR BASIC Computer
Required Components:The component list for this computer is fairly low as only a single IC is required: 1 x ATmega 1284P Microcontroller 1 x DIL 40 Pin 0.6" IC Holder 1 x 40 Pin Female Pin Header (to be cut down into smaller headers) 1 x 16 MHz Crystal...

|<
<
1
2
3
4
5
>
>|